Preferred orientation of ZnO thin films deposited by the atomic layer deposition (ALD) technique could be manipulated by deposition temperature. In this work, diethyl zinc (DEZn) and deionized water (H(2)O) were used as a zinc source and oxygen source, respectively. The results demonstrated that (10.0) dominant ZnO thin films were grown in the temperature range of 155-220 °C. The c-axis crystal growth of these films was greatly suppressed. Adhesion of anions (such as fragments of an ethyl group) on the (00.2) polar surface of the ZnO thin film was believed to be responsible for this suppression. In contrast, (00.2) dominant ZnO thin films were obtained between 220 and 300 °C. The preferred orientations of (10.0) and (00.2) of the ZnO thin films were examined by XRD texture analysis. The texture analysis results agreed well with the alignments of ZnO nanowires (NWs) which were grown from these ZnO thin films. In this case, the nanosized crystals of ZnO thin films acted as seeds for the growth of ZnO nanowires (NWs) by chemical vapor deposition (CVD) process. The highly (00.2) textured ZnO thin films deposited at high temperatures, such as 280 °C, contained polycrystals with the c axis perpendicular to the substrate surface and provided a good template for the growth of vertically aligned ZnO NWs.
Effluent discharges from industry and domestic waste containing unknown inorganic pollutants. In this work, different mechanisms of heavy metal ions removal using ZnO particles were studied. ZnO particles were synthesized using solid precipitation technique. The morphology of ZnO particles was rod-like shape. The average length and diameter of ZnO particle were 497.34 ± 15.55 and 75.78 ± 10.39nm, respectively. These particles removed effectively heavy metal ions such as Cu(II), Ag(I) and Pb(II) ions with efficiency >85% under exposure of 1 hour of UV light. However, poor removal efficiency, i.e. <15% was observed for Cr(VI), Mn(II), Cd(II) and Ni(II) ions. The removal of these heavy metal ions was in the forms of metals or metal oxide via reduction/oxidation or adsorption mechanism.
MXene sheets, as new 2D nanomaterials, have been used in many advanced applications due to their superior thin-layered architecture, as well as their capability to be employed as novel nanocontainers for advanced applications. In this research, intercalated Ti 3 C 2 MXene sheets were synthesized through an etching method, and then they were modified with 3aminopropyltriethoxysilane (APTES). Cerium cations (Ce 3+ ) as an eco-friendly corrosion inhibitor were encapsulated within Ti 3 C 2 MXene sheets to fabricate novel self-healing epoxy nanocomposite coatings. The corrosion protection performance (CPP) of Ce 3+ -doped Ti 3 C 2 MXene nanosheets (Ti 3 C 2 MXene-Ce 3+ ) in a 3.5 wt % sodium chloride (NaCl) solution was studied on bare mild steel substrates using electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization measurements. The self-healing CPP of epoxy coatings loaded with 1 wt % undoped and doped Ti 3 C 2 MXene was evaluated using EIS, salt spray, and field emission scanning electron microscopy (FE-SEM) techniques. The introduction of Ti 3 C 2 MXene-Ce 3+ into the corrosive solution and artificially scribed epoxy coating enhanced the total impedance from 717 to 6596 Ω cm 2 and 8876 to 32092 Ω cm 2 , respectively, after 24 h of immersion compared to the control samples.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.