The structure and properties of discs from cast coarse-grained D16 alloy have been investigated with the help of optical metallography and transmission electron microscopy, after the traditional heat treatment (HT) modes or subjected to high pressure torsion (HPT) under pressure in 6 GPa at room temperature. Standard HT modes included: Т4 (hardening 495°С + natural aging at room temperature for 5 days) and Т6 (hardening 495°С + artificial aging at 185°С for 10 hours). It is shown that after HT of alloy D16 according to modes T6 and Т4, the sizes of the structural elements, compared with the original, decreased by about 4,8 times and the microhardness increased by 1,6 times. It is shown that after one or ten rotates of HPT in D16 alloy the sizes of structural elements, in comparison with initial, decreased by 393 and 899 times, and microhardness increased by 2,4 and 2,9 times, respectively. Detection of hardening hard, brittle and high-alloy copper γ2- phases (Cu9Al4) indicates the passage in the HPT process of the decomposition of a supersaturated solid solution (dynamic aging) in the planes of a local shift.
Methods of the optical metallography, TEM, SEM-technique, tests for hardness and wear resistance are used to investigated the structural - phase transformation in metal blanks from alloy VT23 at cutting treatment in an interval of speeds 2...120 m/min are given. The patterns of interaction of dynamic plastic deformation and destructions on macro-, meso-, micro-and nanolevels are determined. It is shown that the formation in metal blank of modulated high-tensile secondary nanostructures promotes a heightening of a protective wearproofity of treated metal blank, but cutting edge, lowering a wearproofity, of the cutting tool.
С помощью оптической металлографии и просвечивающей электронной микроскопии исследованы структура и свойства заготовок из горячепрессованного крупнозернистого сплава Д16 после традиционных режимов термической обработки (ТО) или подвергнутых интенсивной пластической деформации кручением (ИПДК) под давлением 6 ГПа при комнатной температуре. Стандартные режимы ТО включали: Т 4 (закалка 495 °С + естественное старение при комнатной температуре в течение пяти суток) и Т 6 (закалка 495 °С + искусственное старение при 185 °С в течение десяти часов). Показано, что после ТО сплава Д16 по режимам Т 6 и Т 4 , размеры зерен, по сравнению с исходными, уменьшились примерно в 4,8 раза, а микротвердость увеличилась в 1,6 раз. После одного или десяти оборотов ИПДК в сплаве Д16 размеры зерен, по сравнению с исходными, уменьшились в 393 и 899 раза, а микротвердость увеличилась в 2,4 и 2,9 раза соответственно. Ключевые слова: нанокристаллические материалы ультрамелкозернистые материалы, интенсивная пластическая деформация, деформационно-термическая обработка, дуралюмин Введение. Ультрамелкозернистые (УМЗ), а также нанокристаллические (НК) металлы и Маргарита Александровна Скотникова -д-р техн. наук, профессор; СПбПУ Петра Великого, Институт машиностроения, материалов и транспорта;
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.