Capillary electrophoresis (CE) was coupled to a micro-electrode-based end-column amperometric detector. The influences of separation voltage, CE buffer concentration, and capillary-to-electrode distance on the observed hydrodynamic voltammetry of dopamine and catechol were studied using a separation capillary with an i.d. of 25 μm. It was found that an increased CE voltage, increased buffer concentration, or decreased capillary-to-electrode distance resulted in a positive shift of the observed half-wave potentials for both dopamine and catechol. At a constant separation current of 1.6 μA, the observed half-wave potential was found to increase with applied separation voltage. Furthermore, when experiments were carried out with a platinum quasi-reference electrode instead of a Ag/AgCl reference electrode, similar shifts in half-wave potential were observed. These results indicate that the observed shifts are an effect of the separation voltage rather than the separation current or a change in the reference potential. The characteristics of end-column detection with and without a fracture decoupler were compared. It was found that the effects of separation voltage, CE buffer concentration, and capillary-to-electrode distance were minimized by the use of a decoupling device. The observed half-wave potentials for dopamine and catechol were more positive when a CE capillary without a decoupler was employed compared to when a decoupler was used. Additionally, using the fracture decoupler, the observed half-wave potentials for both dopamine and catechol were approximately the same as when no CE voltage was applied (i.e., when the hydrodynamic voltammograms were recorded under flow injection conditions).Capillary electrophoresis (CE) is a powerful and highly efficient separation technique. Most commercial CE instruments are equipped with a UV absorbance detector. However, due to a limited path length of the light, this detection technique may lack sufficient sensitivity for certain applications. 1 To increase the detection sensitivity in CE, laser-induced fluorescence 2,3 and amperometric 1,4-8 detection have been successfully employed. While LIF detection generally requires a derivatization of the analytes and comprises expensive and complex instrumentation, electrochemical detectors are relatively simple and inexpensive. However, the use of CE with electrochemical detection (CEEC) has been limited. In our opinion, this is mainly due to the perceived difficulty in assembling a CEEC system. The difficulty arises from the need to either use very small inner diameter (i.d.) capillaries and carefully align a microelectrode, or to construct an electrical decoupler between the CE separation capillary and the detection capillary.* To whom correspondence should be addressed. Phone: (785) The use of CEEC was first reported by Wallingford and Ewing in 1987. 9 In that first report, a porous glass joint was employed to electrically decouple the amperometric detector from the electrophoresis system. Several approaches to ...

A new approach for sensitive detection on a microfabricated chip is presented. Indirect laser-induced-fluorescence (IDLIF) was used to detect explosive compounds after separation by micellar electrokinetic chromatography (MEKC). The detection setup was used in an epifluorescence configuration with excitation provided by a near-IR diode laser operating at 750 nm. To achieve indirect detection, a low concentration of a dye (5 microM Cy7) was added to the running buffer as a visualizing agent. Using this methodology, a sample containing 14 explosives (EPA 8330 mixture) was examined. Concentrations of 1 ppm of trinitrobenzene (TNB), trinitrotoluene (TNT), dinitrobenzene (DNB), tetryl, and 2,4-dinitrotoluene (2,4-DNT) could be detected with S/N ratios between 3 and 10. Analyses showing 10 peaks, with plate numbers on the order of 60000, were completed within 60 s using a 65 mm long separation channel. The three isomers of nitrotoluene (2-, 3-, and 4-nitrotoluene) were not resolved. Additionally, the two nitramines (HMX and RDX) could only be detected at much higher concentrations, likely due to the low fluorescence quenching efficiencies of these compounds. The analysis method was also used to separate and detect nitroaromatic compounds in extracts from spiked soil samples. The presence of 1 ppm (1 microg of analyte/1 g of soil) of TNB, DNB, TNT, tetryl, 2,4-DNT, 2,6-DNT, 2-NH2-4,6-DNT, and 4-NH2-2,6-DNT could readily be detected. In the interest of increasing the sensitivity of the analysis, various on-chip injection schemes were evaluated. It was found that a 250 microm double-T injector gave a 35% increase in peak signal compared to a straight-cross injector, which is less than expected based on injected volume.

Amphetamine and analogous compounds have been labeled with 4-fluoro-7-nitrobenzofurazane and analyzed on a microfabricated chip. Separation of norephedrine, ephedrine, cathinone, pseudoephedrine, methcathinone, amphetamine and methamphetamine is demonstrated using micellar electrokinetic capillary chromatography (MEKC) and laser-induced fluorescence (LIF) detection. Chiral separations of individual drugs were studied using neutral and negatively charged cyclodextrins (CDs) with and without the addition of an organic modifier and/or sodium dodecyl sulfate (SDS). The best results were obtained using a highly sulfated gamma-CD (HS-gamm-CD) in combination with a low concentration of SDS. To obtain complete separation of a mixture of (+/-)-norephedrine, (+/-)ephedrine, (+/-)-pseudoephedrine, (+/-)-methcathinone, (+/-)-amphetamine and (+/-)-methamphetamine it was necessary to add a small amount (1.5 mM) of SDS to the separation buffer. Optimized chiral separation was achieved within 7 min using an S-folded separation channel, a separation voltage of 8 kV and a buffer consisting of 50 mM phosphate (pH 7.35), 10 mM HS-gamma-CD and 1.5 mM SDS.

Indirect laser-induced fluorescence detection of explosive compounds using capillary electrochromatography and micellar electrokinetic chromatographyMixtures of nitroaromatic and nitramine explosive compounds and their degradation products were analyzed using electrokinetically driven separations with both indirect laser-induced fluorescence (IDLIF) and UV absorption detection. Complete separations of the 14-component mixture (EPA 8330) were achieved using both capillary electrochromatography (CEC) and micellar electrokinetic chromatography (MEKC). IDLIF detection was performed using an epifluorescence system with excitation provided by a 635 nm diode laser and micromolar concentrations of the dye Cy-5 as the visualizing agent. While the sensitivity of the two detection methods was similar for the nitroaromatic compounds, the nitramines could only be detected using UV absorption due to their low fluorescence quenching efficiency of Cy-5. The detection sensitivity using IDLIF was limited by low frequency oscillations in the fluorescence background. The oscillations increased with higher electric field strength and were attributed to thermal fluctuations caused by Joule heating. Due to the more conductive running buffer and higher separation currents used in MEKC, sensitive IDLIF detection could only be achieved using low (~100 V/cm) field strengths, resulting in long analysis times. CEC separations, which are typically run with low conductivity mobile phases to avoid bubble formation, are less sensitive to this effect. In CEC separations with IDLIF detection a stable fluorescence background using Cy-5 could be established using only a nonporous stationary phase. In capillaries packed with porous silica particles, anomalous migration behavior was observed with charged dye molecules and a stable fluorescence background could not be established under electrokinetic flow. This is the first demonstration of IDLIF in packed channel CEC.