One of the major challenges to the widespread application of the solar chimney power plant is its low-power conversion efficiency because of the three technological processes involved. The chimney efficiency is difficult to improve, and thus enhancing the collector or turbine performance can considerably improve the total plant efficiency. This work focused on enhancing the energy conversion efficiency of the collector and also extending the operation time using a heat storage medium. The solar to thermal conversion and thermal storage capabilities of six ground materials that are potentially available in Malaysia were studied experimentally and numerically. The experimental model was designed such that the six materials were exposed to the same operation boundary conditions. The numerical studies were conducted using ANSYS software, where the geometrical models were developed and simulated using FLUENT for the fluid flow and energy/thermal field studies. The selected ground materials were ceramic, black stones, sawdust, dark-green painted wood, sand, and pebbles. The simulation and experimental results are in good agreement in terms of air stream velocity and energy conversion efficiency. The results showed that the different materials have different heat storage capacities, and that ceramics extend the operation with improved efficiency until nighttime. The results also showed that ceramic and black stones have better performance than the other materials. However, black stones are recommended as the absorbing material for solar chimney power plants in Malaysia and regional countries because they are readily available.

Before being fed into the separators, a pump is often used to maintain adequate flowing pressure of oil/ water emulsion in a production conduit, especially in a depleted or matured reservoir. Droplet shearing and size reduction due to the pump highly affect the separation performance. This paper aims to present an experimental investigation on the shearing of oil droplets in an oil/water production fluid passing through a high rpm single-stage centrifugal pump (C-pump) and a lower rpm gear pump. A cross polarizer microscope has achieved sample analyses. The experiments have been carried out at various water/oil ratios, from 70/30 to 90/10, with two different temperatures of 50 o C and 80 o C. Further, the viscosities of the fluid sample from both pump outlets are correlated with the water cuts. The results are presented in a graphical format showing the droplet size distributions of different cases from the two tested pump types. There is a general trend of higher shear intensity and smaller mean oil droplets with the C-pump than the gear pump. Water cut and the temperature seem to have a small effect on the shearing of the droplets. Further, the viscosity correlation for the fluid collected from two pump outlets at different temperatures and water cuts shows a slight decrease in viscosity with the shear rate. However, it is highly affected by the water cut and temperature.

An existing PV system is cooled by heat dissipation to air by straight fins arrays attached at the backside of the panels. However, a little average temperature drop has been achieved in the plant. The current research aims to simulate and investigate the low cooling performance experienced in the plant and recommend improved PV cooling by backside installed fins. A CAD model was constructed with CATIA software and imported to ANSYS-Fluent to simulate and investigate the cause of low cooling performance. In addition, cooling performance by 45°, 90°and 135° have been studied. The solar PV panel has 1000-mm-width and 2000-mm-length, whereas the fins' base dimensions are 830-mmwidth, and 1260-mm-length and each fin has 80-mm-height. The reference case study's average temperature measured in the actual site is 46.9℃, while the simulation prediction is 48.4℃. The 3.3% difference suggests that the simulation procedure is sufficient to investigate the other cases. Solar PV is paired with the fins air cooling system, stimulating the PV/T with only a 2.7% difference between the actual measurements and the simulation prediction. The bare panel simulation results predicted the backside temperature to be 13.4℃ above the ambient temperature. The 45° and 90° oriented fins reduced the backside temperature to 4.2℃ and 9.54℃ above the ambient temperature. In contrast, the 135° oriented fins have a negative cooling effect, as they increased the backside temperature to 19.05℃ above the ambient temperature. The analysis suggests that the low-performing cooling in the physical system is due to the bad thermal contact between the array base plate and the panel's backside.

This paper was aimed to examine the removal of oil from water by photocatalytic advance oxidation under solar light. A pH of 11 has shown a higher oil removal efficiency. Oil remove efficiency levels at pH 11 have been found 75% within 230 minutes’ oily water effluent, studies have shown that Langmuir isotherm has been the best-fit one of the isotherms for the removal of oil. Data have shown a higher adsorptive capacity. Also we have studied another parameter like (catalyst concentration, initial oil concentration and pH). While the treatment of waste-water is dependent upon a great level of quality for the processed industrial water, the nature of wastes that are added throughout the utilization, and the treatment degree that has been received by the waste-water. Then, the data of the waste-water quality that has been measured rou-tinely and it was reported at the plants of the waste-water treatments are mainly for disposal of the treated effluent or the necessities of the discharge in terms of the gross pollution parameters.

The present work presents a hybrid solar thermal drying of Tilapia fish to improve the product quality and satisfy the importers. The developed hybrid dryer utilized direct solar drying, a solar air heater and a thermal backup unit which sustains the drying process during the night, cloudy and rainy weather conditions. Besides, a new feature of the developed dryer utilizes the flue gas exhausted from the thermal unit to enhance the updraft in the drying chamber by re-injection of the flue gases in the chimney. The initial moisture content of the Tilapia fish used in the investigation was 246.6% on a dry basis, equivalent to 74% on a wet basis. The investigations were repeated three times on different days. Experimental results showed that the moisture content was reduced to an average final of 17.0% db (5.0% wb) within 17.5 hours, while in the open sun drying, it required around 48-72 hours. Hybrid solar drying required around 72% shorter time than open sun drying. The average overall drying efficiency of the developed system for drying Tilapia fish was 13.0%. The Re-injection technique used in the present hybrid solar-thermal system has excluded the need for an electric source for air extraction from the drying chamber, which is highly desired in the rural and fishery regions.

In this work, the photocatalytic is related to simulated wastewater as well as recycling for industrial uses. Photocatalytic degradation of simulated wastewater content (Eosin Yellowish, Eriochrom Black T, Methyl Violet, EDTA, FeSO4.7H2O, NaCl, and NaOH) was utilized as a treatment approach in batch reactors within solar light in a heterogeneous slurry with the use of many concentrations regarding the commercial powder ZnO as photocatalysts semiconductors. We have tested many operation conditions like (catalyst concentration, pH, initial dye concentration and final water treated properties). The water quality related to treated wastewater is based on the nature of waste added during usage, the industrial water supply quality, and the treatment degree which is received via wastewater. After that, the quality data of wastewater is evaluated and indicated at waste-water treatment plant majorly for the disposal of the treated effluents or discharge requirements with regard to gross pollution parameter.

No abstract

No abstract