Recent works suggest Proterozoic plate convergence along the southeastern margin of India which led to amalgamation of the high grade Eastern Ghats belt (EGB) and adjoining fold-and-thrust belts to the East Dhrawar craton. Two major thrusts namely the Vellikonda thrust at the western margin of the Nellore Schist belt (NSB) and the Maidukuru thrust at the western margin of the Nallamalai fold belt (NFB) accommodate significant upper crustal shortening, which is indicated by juxtaposition of geological terranes with distinct tectonostratigraphy, varying deformation intensity, structural styles and metamorphic grade. Kinematic analysis of structures and fabric of the fault zone rocks in these intracontinental thrust zones and the hanging wall and footwall rocks suggest spatially heterogeneous partitioning of strain into various combinations of E-W shortening, top-to-west shear on stratum parallel subhorizontal detachments or on easterly dipping thrusts, and a strike slip component. Although relatively less prominent than the other two components of the strain triangle, non-orthogonal slickenfibres associated with flexural slip folds and mylonitic foliationstretching lineation orientation geometry within the arcuate NSB and NFB indicate left lateral strike slip subparallel to the overall N-S trend. On the whole an inclined transpression is inferred to have controlled the spatially heterogeneous development of thrust related fabric in the terrane between the Eastern Ghats belt south of the Godavari graben and the East Dharwar craton.

The shear strength reduction technique is becoming more and more popular to determine the factor-of-safety for geotechnical constructions, especially for slopes. At present, two in principal different procedures are used to apply the numerical shear strength reduction technique for materials characterised by non-linear failure envelopes, like the HoekBrown criterion. One procedure is based on the determination on local stress and strength values, whereas the other is based on a global linearization of the non-linear failure envelope. This article shortly describes and discusses these two different procedures and compares results for a broad spectrum of parameter constellations based on slope stability calculations. The local approach is physically more correct. The global approach can be considered as a first approximation. A comparison of both methods reveal that the global approach in comparison to the local approach, can leads to a deviation of up to 15 % in both directions. If one considers the local approach as the 'correct' one, depending on the parameters the results of the global approach can lie on the safe or unsafe site. The practical conclusion is that evaluation of slope stability using the global approach can result in uneconomic slope design or overestimation of safety margin. The use of the local approach instead of the global should be preferred. In case of small safety margins (e.g. 20 % or less) the use of the local approach is strictly recommended.

Syntectonic plutons emplaced in shallow crust often contain intermediate-to low-temperature deformation microstructures but lack a high-temperature, subsolidus deformation fabric, although the relict magmatic fabric is preserved. The Proterozoic Vellaturu granite emplaced at the eastern margin of the northern Nallamalai fold belt, south India during the late phase of regional deformation has a common occurrence of intermediate-to low-temperature deformation fabric, superimposed over magmatic fabric with an internally complex pattern. But high-T subsolidus deformation microstructure and fabric are absent in this pluton. The main crystal plastic deformation and fluid enhanced reaction softening was concentrated along the margin of the granite body. Resulting granite mylonites show Y-maximum c-axis fabric in completely recrystallized quartz ribbons, dynamic recrystallization of perthites, and myrmekite indicative of fabric development under intermediate temperature (∼ 500-400 • C). The weakly-deformed interior shows myrmekite, feldspar microfracturing and limited bulging recrystallization of quartz. The abundance of prism subgrain boundaries is indicative of continuing deformation through low-temperature (∼ 300 • C). The relative rates of cooling influenced by advective heat transfer and deformation of the pluton seem to control the overall subsolidus fabric development. The rapid advective heat transfer from the interior in the early stages of subsolidus cooling was followed by slow cooling through intermediate temperature window as a well-developed phyllosilicate rich mylonitic skin around the granite body slowed down conductive heat loss. Low-T crystal plastic deformation of quartz was effected at a late stage of cooling and deformation of the shallow crustal granite body emplaced within the greenschist facies Nallamalai rocks.