The development and evaluation of a controlled-release (CR) pharmaceutical solid dosage form comprising xanthan gum (XG), low molecular weight chitosan (LCS) and metoprolol succinate (MS) is reported. The research is, partly, based upon the utilization of computational tools; in this case molecular dynamics simulations (MDs) and response surface method (RSM), in order to underpin the design/prediction and to minimize the experimental work required to achieve the desired pharmaceutical outcomes. The capability of the system to control the release of MS was studied as a function of LCS (% w/w) and total polymer (LCS and XG) to drug ratio (P:D) at different tablet tensile strengths. MDs trajectories, obtained by using different ratios of XG:LCS as well as XG and high molecular weight CS (HCS), showed that the driving force for the interaction between XG and LCS is electrostatic in nature, the most favourable complex is formed when LCS is used at 15 % (w/w) and, importantly, that the interaction between XG and LCS is more favourable than that between XG and HCS. RSM outputs revealed that the release of the drug from the LCS/XG matrix is highly dependent on both the % LCS and the P:D ratio and that the required CR effect can be achieved when using weight fractions of LCS ≤ 20% and P:D ratios ≥ 2.6:1. Results obtained from in-vitro drug release and swelling studies on the prepared tablets showed that using LCS at the weight fractions suggested by MDs and RSM data plays a major role in overcoming the high sensitivity of the controlled drug release effect of XG on ionic strength and pH changes of the dissolution media. In addition, it was found that polymer relaxation is the major contributor to the release of MS from LCS-XG tablets. Using Raman spectroscopy, MS was shown to be localized more in the core of the tablets at the initial stages of dissolution due to film formation between LCS and XG on the tablet surface which prevents excess water penetration into the matrix. In the later stages of the dissolution process, the film starts to dissolve/erode allowing full tablet hydration and a uniform drug distribution in the swollen tablet.

Hydrophilic matrices composed of chitosan (CS) and xanthan gum (XG) complexes are of pharmaceutical interest in relation to drug delivery due to their ability to control the release of active ingredients. Molecular dynamics simulations (MDs) have been performed in order to obtain information pertaining to the effect of the state of protonation and degree of N-acetylation (DA) on the molecular conformation of chitosan and its ability to interact with xanthan gum in aqueous solutions. The conformational flexibility of CS was found to be highly dependent on its state of protonation. Upon complexation with XG, a substantial restriction in free rotation around the glycosidic bond was noticed in protonated CS dimers regardless of their DA, whereas deprotonated molecules preserved their free mobility. Calculated values for the free energy of binding between CS and XG revealed the dominant contribution of electrostatic forces on the formation of complexes and that the most stable complexes were formed when CS was at least half-protonated and the DA was ≤50%. The results obtained provide an insight into the main factors governing the interaction between CS and XG, such that they can be manipulated accordingly to produce complexes with the desired controlled-release effect.

The development and validation of a quality by design based process analytical tool for the inline quantification of Ramipril during hot-melt extrusion

The subject of our research is the optimization of direct compression (DC), controlled release drug matrices comprising chitosan/xanthan gum. The foregoing is considered from two main perspectives; the use of low molecular weight chitosan (LCS) with xanthan gum (XG) and the determination of important attributes for direct compression of the mixtures of the two polymers. Powder flow, deformation behaviour, and work of compression parameters were used to characterize powder and tableting properties. Compression pressure and LCS content within the matrix were investigated for their influence on the crushing strength of the tablets produced. Response surface methodology (RSM) was applied to determine the optimum parameters required for DC of the matrices investigated. Results confirm the positive contribution of LCS in enhancing powder compressibility and crushing strength of the resultant compacts. Compactibility of the XG/LCS mixtures was found to be more sensitive to applied compression pressure than LCS content. LCS can be added at concentrations as low as 15% w/w to achieve hard compacts, as indicated by the RSM results. The introduction of the plasticity factor, using LCS, to the fragmenting material XG was the main reason for the high volume reduction and reduced porosity of the polymer mixture. Combinations of XG with other commonly utilized polymers in controlled release studies such as glucosamine, hydroxypropyl methylcellulose (HPMC), Na alginate (ALG), guar gum, lactose and high molecular weight (HMW) chitosan were also used; all the foregoing polymers failed to reduce the matrix porosity beyond a certain compression pressure. Application of the LCS/XG mixture, at its optimum composition, for the controlled release of two model drugs (metoprolol succinate and dyphylline) was examined. The XG/LCS matrix at 15% w/w LCS content was found to control the release of metoprolol succinate and dyphylline. The former preparation confirmed the strong influence of compression pressure on changing the drug release profile. The latter preparation showed the ability of XG/LCS to extend the drug release at a fixed rate for 12 h of dissolution time after which the release became slightly slower.

No abstract