No abstract

Background: Previous cadaveric kinematic studies on acromioclavicular injuries described mainly rotational differences during humerothoracic movements. Although isolated scapulothoracic movements are also often performed during activities of daily life and can be painful after acromioclavicular injuries, they have not been extensively studied. Further, the analysis of joint translations in kinematic studies has received little attention compared with biomechanical studies. Hypothesis: A kinematic analysis of joint motions in the intact shoulder versus a shoulder with Rockwood V injury would demonstrate a different pattern of kinematic alterations during humerothoracic and scapulothoracic movements. Study design: Descriptive laboratory study. Methods: A kinematic analysis was performed in 14 cadaveric shoulders during 3 humerothoracic passive movements (coronal and sagittal plane elevation and horizontal adduction) and 3 scapulothoracic passive movements (protraction, retraction, and shrug). An optical navigation system registered rotational motions in the sternoclavicular, scapulothoracic, and acromioclavicular joints in the intact and Rockwood V conditions. In the acromioclavicular joint, mediolateral, anteroposterior, and superoinferior translations were also analyzed. Results: In the Rockwood V condition, a significant increase in clavicular elevation in the sternoclavicular joint during both humerothoracic and scapulothoracic movements was demonstrated, whereas a significant decrease in posterior rotation of the clavicle occurred only during humerothoracic movements. In the scapulothoracic joint, the scapular position changed most significantly during protraction. In the acromioclavicular joint, the scapular tilting position was altered significantly during both humerothoracic and scapulothoracic movements, whereas the scapular rotational position changed only during coronal and sagittal plane elevation. The largest significant changes in the scapular protraction position were seen during protraction movement. Further, in the acromioclavicular joint there was a significant inferior translation of the scapula during all motions, a significant anterior translation during protraction and horizontal adduction, and a significant posterior translation during coronal plane elevation. Mediolaterally, the acromial end of the scapula slid further under the distal clavicle during protraction than during horizontal adduction. Conclusion: Large kinematic differences were seen between the intact state and a Rockwood V lesion not only during humerothoracic movements but also during scapulothoracic movements in the cadaveric model. During humerothoracic movements, rotational differences were mainly caused by alterations in the clavicular position. In contrast, during protraction, the alterations in the scapular position were the dominant factor. Clinical Relevance: This study demonstrates that protraction induces larger kinematic alterations than horizontal adduction in acromioclavicular injuries and can therefore be included in both clinical examination and kinematic analyses to identify lesions more clearly.

Aims Inadvertent soft tissue damage caused by the oscillating saw during total knee arthroplasty (TKA) occurs when the sawblade passes beyond the bony boundaries into the soft tissue. The primary objective of this study is to assess the risk of inadvertent soft tissue damage during jig-based TKA by evaluating the excursion of the oscillating saw past the bony boundaries. The second objective is the investigation of the relation between this excursion and the surgeon’s experience level. Methods A conventional jig-based TKA procedure with medial parapatellar approach was performed on 12 cadaveric knees by three experienced surgeons and three residents. During the proximal tibial resection, the motion of the oscillating saw with respect to the tibia was recorded. The distance of the outer point of this cutting portion to the edge of the bone was defined as the excursion of the oscillating saw. The excursion of the sawblade was evaluated in six zones containing the following structures: medial collateral ligament (MCL), posteromedial corner (PMC), iliotibial band (ITB), lateral collateral ligament (LCL), popliteus tendon (PopT), and neurovascular bundle (NVB). Results The mean 75th percentile value of the excursion of all cases was mean 2.8 mm (SD 2.9) for the MCL zone, mean 4.8 mm (SD 5.9) for the PMC zone, mean 3.4 mm (SD 2.0) for the ITB zone, mean 6.3 mm (SD 4.8) for the LCL zone, mean 4.9 mm (SD 5.7) for the PopT zone, and mean 6.1 mm (SD 3.9) for the NVB zone. Experienced surgeons had a significantly lower excursion than residents. Conclusion This study showed that the oscillating saw significantly passes the edge of the bone during the tibial resection in TKA, even in experienced hands. While reported neurovascular complications in TKA are rare, direct injury to the capsule and stabilizing structures around the knee is a consequence of the use of a hand-held oscillating saw when making the tibial cut. Cite this article: Bone Joint J 2020;102-B(10):1324–1330.

Background Optical tracking systems (OTSs) are essential components of many modern computer assisted orthopaedic surgery (CAOS) systems but patient movement is often neglected in the evaluation of the accuracy. The aim of this study was to develop a representative test to assess the accuracy of OTSs including patient movement and demonstrate the effect of pointer design and OTS choice. Method A mobile phantom with dynamic reference base (DRB) attached was designed and constructed. The point registration trueness and precision were evaluated for measurements with both a static and moving phantom. Results The trueness of the total target registration error (TTRE) was 1.4 to 2.7 times worse with a moving phantom compared to a static phantom. Conclusion The accuracy of OTSs for CAOS applications should be evaluated by measurements with a moving phantom as the evaluation of the TTRE with a static frame significantly underestimates the measurement error.