No abstract

Within braided pneumatic Muscle Actuators (pMA) the braid structure is vital to the actuator's performance, preventing over-inflation, converting radial expansion into axial contraction and setting limits for both dilation and contraction. This paper seeks to explore the nature of the contractile limit and the hysteresis observed by researchers during the actuation cycle. Maximum actuator dilation occurs when adjacent braid strands are forced against one another. Within this work this is analyzed mathematically and it is shown that by halving the number of strands used to create the braided shell the actuator's contractile range can be increased by approximately 7%. This also results in a simultaneous peak contractile force increases of over 16%. These results are verified experimentally. Hysteresis due to friction between braid strands during muscle operation is also explored. The paper will show how consideration of the deformation of the strands allows the contact area and therefore friction to be calculated without the need for experimentally obtained data as in previous research. A mathematical model is produced and verified experimentally.

No abstract

Pneumatic technology has been successfully applied for over two millennia. Even today, pneumatic cylinder based technology forms the keystone of many manufacturing processes where there is a need for simple, high-speed, low-cost, reliable motion. But when the system requires accurate control of position, velocity or acceleration profiles, these actuators form a far from satisfactory solution. Braided pneumatic muscle actuators (pMAs) form an interesting development of the pneumatic principle offering even higher power/weight performance, operation in a wide range of environments and accurate control of position, motion and force. This technology provides an interesting and potentially very successful alternative actuation source for robots as well as other applications. However, there are difficulties with this approach due to the following. (i) Modeling errors. Models of the force response are still nonoptimal and for good results these models are highly complex, which makes accurate design difficult. (ii) Low bandwidth-the bandwidth of the actuator-link assemblies are often considered to be too low for practical success in many applications, particularly robotics.

No abstract

This article presents the design of a variable stiffness, soft, three-fingered dexterous gripper. The gripper uses two designs of McKibben muscles. Extensor muscles that increase in length when pressurized are used to form the fingers of the gripper. Contractor muscles that decrease in length when pressurized are then used to apply forces to the fingers through tendons, which cause flexion and extension of the fingers. The two types of muscles are arranged to act antagonistically and this means that by raising the pressure in all of the pneumatic muscles, the stiffness of the system can be increased without a resulting change in finger position. The article presents the design of the gripper, some basic kinematics to describe its function, and then experimental results demonstrating the ability to adjust the bending stiffness of the gripper's fingers. It has been demonstrated that the fingers' bending stiffness can be increased by more than 150%. The article concludes by demonstrating that the fingers can be closed loop position controlled and are able to track step and sinusoidal inputs.

Soft robot arms possess unique capabilities when it comes to adaptability, flexibility, and dexterity. In addition, soft systems that are pneumatically actuated can claim high power-to-weight ratio. One of the main drawbacks of pneumatically actuated soft arms is that their stiffness cannot be varied independently from their end-effector position in space. The novel robot arm physical design presented in this article successfully decouples its end-effector positioning from its stiffness. An experimental characterization of this ability is coupled with a mathematical analysis. The arm combines the light weight, high payload to weight ratio and robustness of pneumatic actuation with the adaptability and versatility of variable stiffness. Light weight is a vital component of the inherent safety approach to physical human-robot interaction. To characterize the arm, a neural network analysis of the curvature of the arm for different input pressures is performed. The curvature-pressure relationship is also characterized experimentally.

This article presents the development of a power augmentation and rehabilitation exoskeleton based on a novel actuator. The proposed soft actuators are extensor bending pneumatic artificial muscles. This type of soft actuator is derived from extending McKibben artificial muscles by reinforcing one side to prevent extension. This research has experimentally assessed the performance of this new actuator and an output force mathematical model for it has been developed. This new mathematical model based on the geometrical parameters of the extensor bending pneumatic artificial muscle determines the output force as a function of the input pressure. This model is examined experimentally for different actuator sizes. After promising initial experimental results, further model enhancements were made to improve the model of the proposed actuator. To demonstrate the new bending actuators a power augmentation and rehabilitation soft glove has been developed. This soft hand exoskeleton is able to fit any adult hand size without the need for any mechanical system changes or calibration. EMG signals from the human hand have been monitored to prove the performance of this new design of soft exoskeleton. This power augmentation and rehabilitation wearable robot has been shown to reduce the amount of muscles effort needed to perform a number of simple grasps.