Nondoped and nitrogen-doped (N-doped) carbon nanofiber (CNF) electrodes were prepared via a floating catalyst chemical vapor deposition (CVD) method using precursors consisting of ferrocene and either xylene or pyridine to control the nitrogen content. Structural and compositional differences between the nondoped and N-doped varieties were assessed using TEM, BET, Raman, TGA, and XPS. Electrochemical methods were used to study the influence of nitrogen doping on the oxygen reduction reaction (ORR). The N-doped CNF electrodes demonstrate significant catalytic activity toward oxygen reduction in aqueous KNO(3) solutions at neutral to basic pH. Electrochemical data are presented which indicate that the ORR proceeds by the peroxide pathway via two successive two-electron reductions. However, for N-doped CNF electrodes, the reduction process can be treated as a catalytic regenerative process where the intermediate hydroperoxide (HO(2)(-)) is chemically decomposed to regenerate oxygen, 2HO(2)(-) <==> O(2) + 2OH(-). The proposed electrocatalysis mechanisms for ORR at both nondoped and N-doped varieties are supported by electrochemical simulations and by measured difference in hydroperoxide decomposition rate constants. Remarkably, approximately 100 fold enhancement for hydroperoxide decomposition is observed for N-doped CNFs, with rates comparable to the best known peroxide decomposition catalysts. Collectively the data indicate that exposed edge plane defects and nitrogen doping are important factors for influencing adsorption of reactive intermediates (i.e., superoxide, hydroperoxide) and for enhancing electrocatalysis for the ORR at nanostructured carbon electrodes.

No abstract

Bimetallic dendrimer-stabilized nanoparticles (DSNs) were used to prepare supported Pt-Au catalysts within the bulk miscibility gap for this binary system. Hydroxy-terminated generation 5 PAMAM dendrimers were used to prepare Cu 0 nanoparticles (NPs). The Cu 0 NPs were subsequently used to reduce K2PtCl4 and HAuCl4, preparing stabilized bimetallic Pt-Au NPs with a 1:1 stoichiometry. The stabilized NPs were adsorbed onto a high surface area silica support and thermally activated to remove the dendrimers. Transmission electron microscopy (TEM), energy dispersive spectroscopy (EDS), and infrared spectroscopy of adsorbed CO showed that this preparation route resulted in NPs in which the two metals are intimately mixed and that the majority of the bimetallic NPs were smaller than 3 nm. Further, the bimetallic NPs were highly active for CO oxidation catalysis near room temperature and showed evidence of CO induced restructuring at ambient temperatures.

A facile method for the direct preparation of carbon nanofiber (CNF) electrodes by pyrolysis of iron(II) phthalocyanine on nickel substrates is reported. Uniform, large area coverage is observed with aligned bundles of CNFs exhibiting bamboo-like, hollow fibril morphology possessing diameters of 40-60 nm and lengths of ∼10 µm. The electrochemical behavior and stability of CNF electrodes as oxygen reduction catalysts were investigated by electrochemical methods. Without necessitation for extensive electrode pretreatment or surface activation, these electrodes demonstrate significant electrocatalytic activity in aqueous KNO 3 solutions at neutral to basic pH for the reduction of dioxygen to hydrogen peroxide, O 2 + H 2 O + 2eh HO 2 -+ OH -. As determined from chronocoulometry, slopes of Anson plots indicate that the overall electrochemical reaction proceeds by the peroxide pathway via two successive two-electron reductions. pH-dependent cyclic voltammetry studies indicate that the CNF electrodes are very active toward adsorption. At pH < 10 the one-electron reduction of O 2 to superoxide is rate limiting, whereas at more alkaline pH the reduction process is limited by the protonation of adsorbed superoxide. This is reflected by a change in measured apparent charge-transfer coefficient (R obs ) from R obs ) 0.5 to R obs ) 1 at neutral and high pH values, respectively. XPS, Raman, and TEM measurements suggest that the disorder in the graphite fibers and the presence of exposed edge plane defects and nitrogen functionalities are important factors for influencing adsorption of reactive intermediates and enhancing electrocatalysis for O 2 reduction.

Metal-semiconductor junctions between Hg and chemically modified n-and p-Si(111) surfaces have been prepared and analyzed using current-voltage and differential capacitance-voltage methods. To understand the role of the interfacial dipole on interfacial charge transfer, silicon surfaces were modified with either nonstoichoimetric oxide (SiO x ), terminal monohydride, short (C n H 2n+1 -, n ) 1, 2, 3) saturated alkyl chains, or propynyl (CH 3 -CtC-) groups. X-ray photoelectron spectra of the modified Si electrode surfaces taken before and after exposure to Hg contacts showed no evidence of irreversible chemical interactions between the Si and the Hg. Hg/Si contacts made using H-terminated Si(111) surfaces exhibited Schottky junctions having barrier heights (Φ b ) that were consistent with the known surface electron affinity of Si and the work function of Hg. In contrast, Si coated with a thin, chemically grown oxide formed Hg/Si junctions having barrier heights suggestive of Fermi level pinning. Si(111) surfaces modified with methyl groups yielded Hg junctions having barrier heights in accord with expectations based on the electron affinity (3.67 eV) and surface dipole (0.38 eV) measured on such surfaces by photoemission spectroscopy, attesting to the degree of chemical control that can be exerted over the barrier heights of such systems by surface functionalization methods. Incomplete coverages of functional groups produced by alkylation with ethyl or iso-propyl groups did not greatly impact the observed values of Φ b relative to Φ b values observed for CH 3 -terminated Si(111) surfaces. However, the observed variation in Φ b between nominally identical samples increased as the number of carbons in the functionalizing alkyl group increased. Junctions between Hg and Si(111) surfaces modified with propynyl groups showed nearly identical behavior to that of CH 3 -Si(111)/Hg contacts, both in average Φ b values and standard deviation between samples. The behavior of Si/Hg interfaces modified with short organic functional groups is consistent with the efficacy and utility of passivated surfaces in modifying the properties of surface-based Si devices.

The solar energy conversion properties of thin Si and GaP nanowire photoelectrodes in photoelectrochemical cells have been examined through sets of finite-element simulations. A discussion describing the motivation behind nanostructured, high aspect ratio semiconductor photoelectrode designs and a brief survey of current experimental results reported for nanostructured semiconductor photoelectrodes in photoelectrochemical cells are presented first. An analysis is then shown that outlines the primary recombination pathways governing the steady-state current-potential behaviors of thin, cylindrical nanowire photoelectrodes, with explicit expressions detailing the differences between planar and cylindrical photoelectrodes arising from the solution of carrier fluxes in planar and cylindrical geometries. Results from finite-element simulations used to model the key features of thin nanowire photoelectrodes under low-level injection conditions are shown that illustrate which recombination pathway(s) is operative under various experimental conditions. Specifically, the respective effects of non-uniform doping, tapering along the length, variation in charge carrier mobilities and lifetimes, changes in nanowire radius, and changes in the density of surface defects on the observable photocurrent-potential responses are reported. These cumulative results serve as guides for future experimental work aimed at improving the attainable solar energy conversion efficiencies of doped semiconductor nanowire photoelectrodes. Lastly, separate simulations that model lightly doped nanowire photoelectrodes under high-level injection conditions are discussed. These results suggest discrete, ohmic-selective contacts may afford a way to circumvent the stringent doping requirements discussed herein for thin nanowire photoelectrodes.

Arrays of Si rods are embedded in PDMS and removed from the rigid growth substrate, resulting in a composite material that merges the benefits of single‐crystalline silicon with the flexibility of a polymer. With this technique, solar cell absorber materials with the potential to achieve high efficiency can be prepared by high‐temperature processing and transformed into a flexible, processable form.

The facile deposition of para-substituted aryl films onto indium-tin oxide (ITO) electrodes by the electrochemical reduction of aryl diazonium salts in acetonitrile is reported. For the deposition conditions used in this report, the aryl film thicknesses are on the order of 1-6 nm, suggesting a multilayer structure. Regardless of the functional group on the aryl diazonium cation, (NO(2), CO(2)H, or fluorene) the electrodeposition behavior onto ITO electrodes is similar to that seen on other electrode materials. XPS and UV-vis data support the introduction of organic functional surface groups to ITO. The blocking behavior of the aryl films on ITO toward the Ru(NH(3))(6)(3+/2+) redox couple is in agreement with electron transfer through conjugated organic layers. The facile preparation of patterned aryl films with regular-spaced 700 nm voids on ITO is also described. Atomic force microscopy and scanning surface potential microscopy on patterned NO(2) aryl films are used to assess the molecular structure and orientation. A 100 mV decrease in the contact potential over NO(2) aryl films relative to bare ITO suggests that the aryl films are loosely structured as deposited with the NO(2) groups oriented at a small angle away from the ITO surface.