International audienceNanocrystalline calcium phosphate apatites constitute the main inorganic part of hard tissues, and a growing focus is devoted to prepare synthetic analogs, so-called "biomimetic", able to precisely mimic the morphological and physico-chemical features of biological apatite compounds. Both from fundamental and applied viewpoints, an accurate characterization of nanocrystalline apatites, including their peculiar surface features, and a deep knowledge of crystallization aspects are prerequisites to attempt understanding mineralization phenomena in vivo as well as for designing innovative bioactive materials that may then find applications in bone tissue engineering, either as self-supported scaffolds and fillers or in the form of coatings, but also in other domains such as drug delivery or else medical imaging. Also,interfacial phenomena are of prime importance for getting a better insight of biomineralization and for following the behavior of biomaterials in or close to their final conditions of use. In this view,both adsorption and ion exchange represent essential processes involving the surface of apatite nanocrystals, possibly doped with foreign elements or functionalized with organic molecules of interest. In this review paper, we will address these various points in details based on a large literature survey. We will also underline the fundamental physico-chemical and behavioral differences that exist between nanocrystalline apatites (whether of biological origin or their synthetic biomimetic analogs) and stoichiometric hydroxyapatite

No abstract

Most of the research performed on calcium phosphate bone cements (CPBCs) has dealt with the improvement of bone cement formulations for new, demanding bone-filling applications. In particular, the development of injectable bone cements is of real interest for the biomedical community. The aim of this work was to study the effect of citric acid on the injectability and the setting properties of alpha-tricalcium phosphate-based cements. A comparative kinetic study was performed on cements with and without citric acid relating the hardening curves and the hydration rates using a mathematical approach. Citric acid behaved as a fluidificant during the first stages of the cement mixing. The dissolution-precipitation reactions of the alpha-tricalcium phosphate were retarded with the addition of citric acid and the compressive strength at saturation increased. In conclusion, citric acid can behave as a water-reducing admixture.

No abstract

Bisphosphonates (BPs) are well established as successful antiresorptive agents for the prevention and treatment of bone diseases such as osteoporosis and Paget's disease. The aim of this work was to clarify the reaction mechanisms between a BP molecule, tiludronate, and the nanocrystalline apatite surface. The adsorption of tiludronate on well-characterized synthetic biomimetic nanocrystalline apatites with homogeneous but different compositions and surface characteristics was investigated to determine the effect of the nanocrystalline apatite substrate on the adsorption behavior. The results show that the adsorption of tiludronate on nanocrystalline biomimetic apatite surfaces varies over a large range. The most immature apatitic samples exhibited the highest affinity and the greatest amount adsorbed at saturation. Maturation of the nanocrystals induces a decrease of these values. The amount of phosphate ion released per adsorbed BP molecule varied, depending on the nanocrystalline substrate considered. The adsorption mechanism, although associated with a release of phosphate ions, cannot be considered as a simple ion exchange process involving one or two phosphate ions on the surface. A two-step process is proposed consisting of a surface binding of BP groups to calcium ions associated with a proton release inducing the protonation of surface orthophosphate ions and their eventual solubilization.

The details of a synthesis method for biologically relevant hydrated calcium pyrophosphates (CPPs, Ca 2 P 2 O 7 ·nH 2 O) has been elucidated. Control of the pH (from 3.6 to 5.8) and the temperature (from 25 to 90°C) during the synthesis enabled the preparation of four pure CPP phases within one hour without intermediates: monoclinic and triclinic calcium pyrophosphate dihydrate (CPPD, Ca 2 P 2 O 7 ·2H 2 O), which are the two CPP phases detected in vivo in joints of arthritic patients, monoclinic tetrahydrate β (CPPT, Ca 2 P 2 O 7 ·4H 2 O) and an amorphous phase (a-CPP, Ca 2 P 2 O 7 ·nH 2 O). Four domains corresponding to the four different phases of hydrated calcium pyrophosphate were identified; a-CPP was synthesised over a very wide pH and temperature range (up to 90°C) within the domain of synthesis conditions explored, including physiological conditions (pH 7.4 and 37°C). The as-synthesised hydrated CPP phases were characterised by complementary techniques (powder X-ray diffraction, FTIR and Raman spectroscopy, scanning electron microscopy and thermogravimetry) and chemical analyses. Rietveld refinement analyses of the as-synthesised crystalline phases were performed, and[a] CIRIMAT,

Apatitic cements have shown excellent biocompatibility and adequate mechanical properties but have slow resorption in the human body. To assure that new bone tissue grows into the bone defect, a certain porosity is necessary although hard to achieve in injectable cements with suitable mechanical properties. An attempt was made by mixing alpha-tricalcium phosphate (alpha-TCP), calcium sulphate hemihydrate (CSH) and an aqueous solution containing 2.5 wt% of Na(2)HPO(4). The aim was to obtain a material containing two phases: a) one apatitic phase (calcium-deficient hydroxyapatite; CDHA) and b) one resorbable phase (calcium sulphate dihydrate; CSD). alpha-TCP and CSH mixtures were produced at relative intervals of 20 wt%. The liquid-to-powder (L/P) ratio to obtain a paste was 0.32 mLg(-1). The highest compressive strength (34 MPa) was obtained for the pure alpha-TCP sample. The strength was, in a first approximation, directly correlated to the weight proportions of the powders. X-ray diffraction analysis showed that the relative intensity for CDHA increased linearly, and the one for CSD decreased exponentially, when the amount of alpha-TCP increased. Thus, CSH ceased to transform to CSD when the amount of alpha-TCP increased. Observations in environmental scanning electron microscopy confirmed the X-ray diffraction results. CSH-crystals (100 microm) were embedded in the HA-matrix permitting gradual porosity in the material when resorbed.

The aim of the current work was to study the physico-chemical interactions of a bisphosphonate molecule, risedronate, with a well-characterised synthetic nanocrystalline apatite (NCA) as a model bone mineral. We adopted a global approach, using complementary physico-chemical techniques such as FTIR, RAMAN and NMR spectroscopies in order to learn more about the interaction process of risedronate with the apatitic surface. The results obtained suggest that risedronate adsorption corresponds to an ion substitution reaction with phosphate ions occurring at the crystal surface. This mechanism explains the greater amount adsorbed (N) for NCA, compared to well crystallised stoichiometric hydroxyapatite, attributable to the well-developed hydrated layer at the surface of the nanocrystals. However, most calcium ions remain attached to the solid phase and the formation of insoluble risedronate calcium salts must also be considered as a competitive reaction to the adsorption. Thus a calcium risedronate salt was synthesised and fully characterised for comparison to the solids after adsorption. Following spectroscopic results, it can be concluded that a strong interaction was established between risedronate ions and calcium ions at the apatitic surface. However, under these experimental conditions there is no nucleation of a distinct calcium risedronate salt and the apatite crystals retain their integrity.