Contact mode atomic force microscopy (AFM) was used to intentionally scratch a monolayer deposited on a pyrolyzed photoresist film (PPF). The force was set to completely remove the monolayer but not to damage the underlying PPF surface. A line profile determined across the scratch with tapping mode AFM permitted determination of the monolayer thickness from the depth of the scratch. A statistical process was devised to avoid user bias in determining the monolayer thickness and was used to determine the thickness as a function of derivatization parameters. PPF surfaces modified by reduction of diazonium ions of stilbene, biphenyl, nitrobiphenyl, terphenyl, and nitroazobenzene (NAB) were scratched and their modification layer thicknesses determined. For single-scan derivatizations of 1 mM diazonium ions to -0.6 V versus Ag+/Ag, the biphenyl and stilbene monolayers exhibited thicknesses close to those expected for true monolayers. However, more extensive derivatization resulted in multilayers up to 6.3 nm thick for the case of NAB. Such multilayers imply that electrons are transmitted through the growing film during diazonium reduction, despite the fact that electron tunneling would not be expected to be operative over such long distances. The results are consistent with a conductance increase in the growing film, which yields a partially conductive layer that can support further diazonium ion reduction and additional layer growth.

Molecular junctions were fabricated consisting of a 3.7 nm thick layer of nitroazobenzene (NAB) molecules between a pyrolyzed photoresist substrate (PPF) and a titanium top contact which was protected from oxidation by a layer of gold. Raman spectroscopy, XPS, and AFM revealed that the NAB layer was 2-3 molecules thick and was bonded to the two conducting contacts by C-C and N-Ti covalent bonds. The current/voltage behavior of the PPF/NAB(3.7)/Ti junctions showed strong and reproducible rectification, with the current at +2 V exceeding that at -2 V by a factor of 600. The observed current density at +3 V was 0.71 A/cm 2 , or about 10 5 e -/s/molecule. The i/V response was strongly dependent on temperature and scan rate, with the rectification ratio decreasing for lower temperature and faster scans. Junction conductivity increased with time over several seconds at room temperature in response to positive voltage pulses, with the rate of increase larger for more positive potentials. Voltage pulses to positive potentials and back to zero volts revealed that electrons are injected from the Ti to the NAB, to the extent of about 0.1-1 e -/molecule for a +3 V pulse. These electrons cause an activated transition of the NAB into a more conductive quinoid state, which in turn causes an increase in conductivity. The transition to the quinoid state involves nuclear rearrangement which occurs on a submillisecond to several second time scale, depending on the voltage applied. The quinoid state is stable as long as the applied electric field is present, but reverts back to NAB within several minutes after the field is relaxed. The results are interpreted in terms of a thermally activated, potential dependent electron transfer into the 3.7 nm NAB layer, which brings about a conductivity increase of several orders of magnitude.

that residual gases in the electron beam evaporator were causing titanium oxide to form during titanium deposition. A lower back pressure and faster Ti deposition rate (4 × 10 -7 Torr and 0.1 nm/s) resulted in a significant change in the appearance of Figure 3, as shown below. XPS depth profiling showed the formation of Ti(II) and Ti(III) oxides using the previous conditions. These results imply that both a Ti/TiO x layer and the NAB/NAB -layer determine the electronic behavior of the junction.Current/voltage curves for PPF/NAB/Ti/Au junctions with Ti deposited under the original conditions (8 × 10 -6 Torr and 0.03 nm/s) and under "low oxide" conditions (4 × 10 -7 Torr and 0.1 nm/s). The scan rate was 1 V/s in both cases. See https://pubs.acs.org/sharingguidelines for options on how to legitimately share published articles.