Multiple impeller reactors are widely used due to their advanced gas utilization and an increased volumetric mass transfer coefficient. However, with the application of Rushton impellers, gas dispersion efficiency varies between the bottom and the upper impeller levels. The present study analyzes the individual flow regime, power input, and gas hold-up in each compartment of a reactor equipped with four Rushton impellers. The results indicate that the pre-dispersion of the air introduced by the bottom impeller (up to 80%) plays a key role in a better gas retention efficiency of the upper impellers (>300%) and leads to a shift of the cavity and flooding lines in the flow map (Fr-vs Fl-Number) of the upper impellers. A novel analysis of the bubble flow in the dispersed state via a two-phase LES-based CFD model reveals that a more homogenous distribution of air bubbles in the upper compartments leads to high compartment gas hold-up values, but fewer bubbles in the vicinity of the impellers. The measured and simulated data of this study indicate that the upper impellers' efficiency mostly depends on the flow regime of and the pre-dispersion by the bottom impeller rather than on the upper impellers' flow regimes. These results contribute to the understanding of essential mixing processes and scaling of aerated bioreactors.
In high-performance industrial fermentation processes, stirring and aeration may account for significant production costs. Compared to the widely applied Rushton impellers, axial-pumping impellers are known to yield a lower power draw and at the same time improve mixing. However, their lower gas dispersion capability requires stronger agitation, compromising these benefits. Diverse advanced impeller forms have been developed to cope with this challenge. We apply alternating radial and axial impellers and demonstrate strong gas dispersion and energy-efficient mixing for the first time in a large-scale (160 m 3 ) bioreactor, based on experimental and computational fluid dynamics simulation data. For equal operating conditions (stirrer speed, aeration rate), this setup yielded similar gas hold-ups and better mixing times (35%) compared to a classical Rushton-only configuration. Hence, applying a radial impeller on an upper level for improving gas dispersion maintains the benefits of axial impellers in terms of reducing energy demand (up to 50%). We conclude that this effect is significant only at large-scale, when bubbles substantially expand due to the release of the hydrostatic pressure and have time to coalesce. The work thus extends current knowledge on mixing and aeration of large-scale reactors using classical impeller types.
The power input and gas-liquid mass transfer rank among the most important industrial fermentation process parameters. The present study analyzes the power input and gas hold-up as a function of the flow regime, impeller diameter, and rheological properties in a pilot scale reactor (160 L) equipped with four Rushton impellers. This leads to four dimensionless numbers for predicting measurements in pilot and industrial bioreactors (110 and 170 m3) with a standard deviation of 7 % to 29 %. This is unparalleled for the underlying aerated and non-Newtonian fermentation broths. Several existing correlation equations are discussed to be dissatisfying (up to 130 % deviation), and might be sufficiently valid only within scale or for small scaling factors. The introduced approach predicts adequately accurate over three orders of magnitude. Based on these encouraging results, we identified the Galilei number and the power concept as the central elements in combination with the consequent dimensional analysis for an efficient scaling betweeen pilot and industrial scale.
In high-performance industrial fermentation processes, stirring and aeration may account for significant production costs. Compared to the widely applied Rushton impellers, axial-pumping impellers are known to yield a lower power draw and at the same time improve mixing. However, their lower gas dispersion capability requires stronger agitation, compromising these benefits. Diverse advanced impeller forms have been developed to cope with this challenge. We apply alternating radial and axial impellers and demonstrate strong gas dispersion and energy-efficient mixing for the first time in a large-scale (160 m ) bioreactor, based on experimental and CFD simulation data. For equal operating conditions (stirrer speed, aeration rate), this setup yielded similar gas hold-ups and better mixing times (-35 %) compared to a classical Rushton-only configuration. Hence, applying a radial impeller on an upper level for improving gas dispersion maintains the benefits of axial impellers in terms of reducing energy demand (up to -50 %). We conclude that this effect is significant only at large-scale, when bubbles substantially expand due to the release of the hydrostatic pressure and have time to coalesce. The work thus extends current knowledge on mixing and aeration of large-scale reactors using classical impeller types.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.