Abstract:We report on a detailed study of the inscription and characterization of fiber Bragg gratings (FBGs) in commercial step index polymer optical fibers (POFs). Through the growth dynamics of the gratings, we identify the effect of UV-induced heating during the grating inscription. We found that FBGs in annealed commercial POFs can offer more stable short-term performance at both higher temperature and larger strain. Furthermore, the FBGs' operational temperature and strain range without hysteresis was extended by the annealing process. We identified long-term stability problem of even the annealed POF FBGs. [7][8][9][10][11][12][13][14][15][16]. 325nm has been employed as a mainstream wavelength for writing grating in PMMA POFs [1][2][3][4][5][8][9][10][11][12][13][14][15]. Other wavelength such as 355nm obtained from a frequency-tripled Nd:YAG laser has been used to write grating in CYTOP fiber developed by Asahi Glass Co. and Keio University [15,16]. On the other hand, 800nm femtosecond pulses from Ti:Sapphire laser or its double frequency was mainly used for point by point direct writing [6] or grating writing with a phasemask [7]. However, the mechanism of index change does not appear to be fully understood [5,13,[18][19][20]. It is believed that more than one process is involved in the photo-induced refractive index changes and hence in the grating formation dynamics [18][19][20]. The widely accepted point is that the principle mechanism of index change is an increase due to the photo-induced polymerization of the unreacted monomers [5,[18][19][20], while laser-induced heating in the irradiated region during the inscription may also contribute to the index change [5]. Previous reports indicated that annealing of the POF before FBG inscription can relieve the frozen-in stress induced by the fiber drawing process [21] and increase the linear operation temperature range of FBGs [22]. However, the effect of annealing on the strain sensitivity performance was not yet considered. Polymer optical FBGs have shown great potential for sensor applications to sense for example temperature and strain with higher sensitivity and wider tunability than its silica counterpart [1][2][3][4][5][6][7][8][9][10][11][12][13][14]. Those advantages are due to the lower Young's modulus and higher thermo-optic coefficient of POFs [23,24]. In addition, polymers are clinically

No abstract

No abstract

Fiber-optical accelerometers based on polymer optical fiber Bragg gratings are reported. We have written fiber Bragg gratings for 1550 nm and 850 nm operations, characterized their temperature and strain response, and tested their performance in a prototype accelerometer.

The demand from industry to produce accurate acceleration measurements down to ever lower frequencies and with ever lower noise is increasing. Different vibration transducers are used today for many different purposes within this area, like detection and warning for earthquakes, detection of nuclear testing, and monitoring of the environment. Accelerometers for such purposes must be calibrated in order to yield trustworthy results and provide traceability to the SI-system accordingly. For these calibrations to be feasible, suitable ultra low-noise accelerometers and/or signal processing functions are needed. <br />Here we present two digital signal processing (DSP) functions designed to measure ultra low-noise acceleration in calibration systems. The DSP functions use dual channel signal analysis on signals from two accelerometers measuring the same stimuli and use the coherence between the two signals to reduce noise. Simulations show that the two DSP functions are estimating calibration signals better than the standard analysis. <br />The results presented here are intended to be used in key comparison studies of accelerometer calibration systems, and may help extend current general low frequency range from e.g. 100 mHz down to ultra-low frequencies of around 10mHz, possibly using somewhat same instrumentation.

We present a fibre optical accelerometer based on a balanced double cantilever design that offers improved performance in terms of sensitivity, frequency range and reliability in general. Within a three year project funded by the Danish National Advanced Technology Foundation, we have developed a rugged prototype with a wavelength sensitivity of 20 pm/g within ±1dB over a frequency range from DC to 1 kHz. These units are currently undergoing field tests in monitoring applications, e.g. for wind turbines, energy services, aerospace etc. In particular, we consider sensitive and reliable accelerometers essential for future condition monitoring and structural health monitoring applications.

In this paper we present our latest work on Fiber Bragg Gratings (FBGs) in microstructured polymer optical fibers (mPOFs) and their application as strain sensing transducers in devices, such as accelerometers and microphones. We demonstrate how the cross-sensitivity of the FBG to temperature is eliminated by using dual-FBG technology and how mPOFs fabricated from different grades of TOPAS with glass transition temperatures around 135 o C potentially allow high-temperature humidity insensitive operation. The results bring the mPOF FBG closer to being a viable technology for commercial applications requiring high sensitivity due to the low Young's Modulus of polymer.

No abstract