No abstract

Nanocomposites based on an ethylene vinyl acetate copolymer (27 wt% vinyl acetate) and various (organomodified) clays have been prepared by melt blending and their morphology, tensile and thermal degradation properties have been evaluated. Special attention has been paid to the influence of the clay nature and origin (montmorillonite or fluoromica) as well as on the nature of the ammonium cation organic modifier. It has been shown that nanostructure and tensile properties mainly depend on the nature of the organic modifier while the delay in thermal volatilisation of EVA during thermo-oxidation is mainly driven by the nature of the clay (mainly its aspect ratio), with no significant influence of the nanostructure of the nature of the organic modifier.

Nanocomposites based on an ethylene–vinyl acetate copolymer (27 wt.‐% vinyl acetate) and multiwall carbon nanotubes (MWNTs) have been prepared by melt blending and their thermal degradation and flame retardant properties have been evaluated. Special attention has been paid to the influence of the nanotube nature on the flammability properties and more particularly on the time to ignition (TTI) as measured by cone calorimetry. It has been shown that there is a strong influence of the nature of carbon nanotubes on the fire behaviour of the composites, especially previous MWNTs crushing proved to substantially delay the TTI while maintaining much reduced heat release rate (HRR). Such a remarkable behaviour might be explained by the chemical reactivity of radical species present at the surface/extremities of crushed MWNTs during the combustion process.

No abstract

No abstract

High‐density polyethylene coated multiwalled carbon nanotubes (c‐MWNTs) and multiwalled carbon nanotubes (MWNTs) have been dispersed into an ethylene vinyl acetate (EVA) copolymer by mechanical kneading. The effect of c‐MWNTs on tensile properties, thermo‐oxidative degradation, and fire behavior has been studied in comparison with virgin EVA and EVA/MWNTs nanocomposites. Due to the better dispersion of the coated nanotubes, the incorporation of 3 wt % of c‐MWNTs leads to an increase of the Young's modulus, the cohesion of the combustion residues, and a decrease of the peak heat‐release rate.

Multi-walled carbon nanotubes (MWNTs) are placed under atomic nitrogen flow formed through an Ar + N 2 microwave plasma in order to functionalize covalently their side walls with nitrogen-containing groups. The MWNT surface analyzed by X-ray photoelectron spectroscopy shows the presence of amides, oximes and mainly amine and nitrile functions grafted in this way. In order to highlight the actual location of the amine functions grafted on MWNTs, they were considered as initiation species in ring-opening polymerization of e-caprolactone using triethylaluminium as activator. The so-generated poly(e-caprolactone) chains remain grafted on the MWNTs via amide bonds and form polyester islets along the nanotubes surface. TEM images of these MWNT surfaces grafted with poly(e-caprolactone) show a good amino-sidewall distribution. This work demonstrates the side-wall amino-functionalization of carbon nanotubes readily achieved by microwave plasma with the possibility to reach within a short time period very high contents in nitrogen-based functions (y10 at.%).

Since their discovery at the beginning of the 1990s, carbon nanotubes (CNTs) have been the focus of considerable research by both academia and industry due to their remarkable and unique electronic and mechanical properties. Among numerous potential applications of CNTs, their use as reinforcing materials for polymers has recently received considerable attention since their exceptional mechanical properties, combined with their low density, offer tremendous opportunities for the development of fundamentally new material systems. However, the key challenge remains to reach a high level of nanoparticle dissociation (i.e. to break down the cohesion of aggregated CNTs) as well as a fine dispersion upon melt blending within the selected matrices. Therefore, this contribution aims at reviewing the exceptional efficiency of CNT coating by a thin layer of polymer as obtained by an in situ polymerization process catalysed directly from the nanofiller surface, known as the ‘polymerization‐filling technique’. This process allows for complete destructuring of the native filler aggregates. Interestingly enough, such surface‐coated carbon nanotubes can be added as ‘masterbatch’ in commercial polymeric matrices leading to the production of polymer nanocomposites displaying much better thermomechanical, flame retardant and electrical conductive properties even at very low filler loading. Copyright © 2007 Society of Chemical Industry