a b s t r a c tBackground: Amon Q2 g various dental materials and their successful restorative uses, titanium provides an excellent example of integrating science and technology involving multiple disciplines of dentistry including biomaterials, prosthodontics and surgical sciences. Titanium and its alloys have emerged as a material of choice for dental implants fulfilling all requirements biologically, chemically and mechanically. Several excellent reviews have discussed the properties of titanium and its surface characteristics that render it biocompatible. However, in most patients, titanium implants are used alongside several other metals. Presence of different metals in the same oral environment can alter the properties of titanium. Other influencing factors include intra-oral pH, salivary content, and effect of fluorides. Highlight: This review discusses the effect of the above-mentioned conditions on the properties of titanium and its alloys. An extensive literature search encompassing the properties of titanium in an altered oral environment and its interaction with other restorative materials is presented. Specific conditions that could cause titanium to corrode, specifically due to interaction with other dental materials used in oral rehabilitation, as well as methods that can be employed for passivation of titanium are discussed. Conclusion: This review presents an overview of the properties of titanium that are vital for its use in implant dentistry. From a restorative perspective, interaction between implant restoration metals, intraoral fluorides and pH may cause titanium to corrode. Therefore, in order to avoid the resulting deleterious effects, an understanding of these interactions is important for long-term prognosis of implant restorations.
The purpose of this study was to examine gender disparities in dental leadership and academics in the United States. Nine journals that represent the dental specialties and high published impact factors were selected to analyze the percentage of female dentists' first and senior authorship for the years 1986, 1990, 1995, 2000, 2005, and 2008. Data on appointment status and female deanship were collected from the American Dental Association (ADA) survey, and the trends were studied. The proportion of female presidents in ADA-recognized specialty organizations was also calculated. Overall, the increase in first female authorship was not statistically significant, but the increase of last female authorship was statistically significant in a linear trend over the years. The percentage of tenured female faculty members and female deans in U.S. dental schools increased by factors of 1.7 and 9, respectively, during the study period. However, female involvement in professional organizations was limited. Findings from this study indicate that female participation in authorship and leadership has increased over time. Nevertheless, females are still a minority in dental academics and leadership.Note: Data are from the American Dental Association. Data on advanced dental education enrollment for years of 1985-86 and 1989-90 and for female faculty for years of 1985-86, 1989-90, and 1995-96 were not available.
Aim This study evaluated the effects of ceramic veneer thicknesses on the polymerization of two different resin cements. Materials and Methods A total of 80 ceramic veneer discs were fabricated by using a pressable ceramic material (e.max Press; Ivoclar Vivadent) from a Low Translucency (LT) ingot (A1 shade). These discs were divided into light-cured (LC; NX3 Nexus LC; Kerr) and dual-cured (DC; NX3 Nexus DC; Kerr) and each group was further divided into 4 subgroups, based on ceramic disc thickness (0.3 mm, 0.6 mm, 0.9 mm, and 1.2 mm). The values of Vickers microhardness (MH) and degree of conversion (DOC) were obtained for each specimen after a 24-hour storage period. Association between ceramic thickness, resin cement type, and light intensity readings (mW/cm2) with respect to microhardness and degree of conversion was statistically evaluated by using ANOVA. Results For the DOC values, there was no significant difference observed among the LC resin cement subgroups, except in the 1.2 mm subgroup; only the DOC value (14.0 ± 7.4%) of 1.2 mm DC resin cement had significantly difference from that value (28.9 ± 7.5%) of 1.2 mm LC resin cement (P<.05). For the MH values between LC and DC resin cement groups, there was statistically significant difference (P<.05); overall, the MH values of LC resin cement groups demonstrated higher values than DC resin cement groups. On the other hands, among the DC resin cement subgroups, the MH values of 1.2 mm DC subgroup was significantly lower than the 0.3 mm and 0.6 mm subgroups (P<.05). However, among the LC subgroups, there was no statistically significant difference among them (P >.05). Conclusion The degree of conversion and hardness of the resin cement was unaffected with veneering thicknesses between 0.3 and 0.9 mm. However, the DC resin cement group resulted in a significantly lower DOC and MH values for the 1.2 mm subgroup. Clinical Significance While clinically adequate polymerization of LC resin cement can be achieved with a maximum 1.2 mm of porcelain veneer restoration, the increase of curing time or light intensity is clinically needed for DC resin cements at the thickness of more than 0.9 mm.
This article presents a method for altering occlusal vertical dimension (OVD) to restore dentitions with limited restorative space due to loss of tooth structure. A provisional increase in OVD is achieved using predominately base metal onlays, which offer advantages over conventional techniques. The onlays are resistant to wear, may be bonded well to nonrestored and restored tooth surfaces with resin cements, and provide a fairly reversible method of increasing OVD. A patient situation is presented which demonstrates the use of provisional base metal onlays in complete mouth rehabilitation.
The aims of this study were to assess 1) differences in perceptions of dental implant training between dental students who received didactic training alone (control group) and those who received didactic plus simulation training (test group); 2) differences in response between students with and without clinical experience in implant dentistry; and 3) the interaction effect of simulation training and clinical experience on students' satisfaction. A survey was distributed to the control group in 2014 and to the test group in 2015; both groups were at the same U.S. dental school. Data were collected on confidence levels with various implant restorative procedures along with overall satisfaction and number of implant restorations performed by each student. The response rate was 78.7% in the control group and 81.3% in the test group. In the control group, 85.7% of students reported being satisfied with implant training compared to 90.8% of students in the test group. The interaction effect of simulation training and clinical experience on overall student satisfaction was OR=1.5 at 95% CI: 0.8, 3.0. The students who had clinical experience with implant restorative procedures had significantly greater satisfaction than those who did not (OR=4.8, 95% CI: 2.1, 11.1, p<0.01). This study found that both the simulation and clinical experience affected these students' confidence and satisfaction levels with implant education: they were almost five times more satisfied with implant training when clinical experience in implant restorative procedures was a part of their implant education.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.