No abstract

Thin, thermoresponsive polymer coatings that allow to reversibly modulate cell adhesion and detachment are attractive substrates for cell sheet engineering. Usually, this is accomplished by applying thin poly(N-isopropylacrylamide) (PNIPAM) coatings, which allow cell adhesion via nonspecific interactions above the collapse temperature (T(T)) of the surface-attached polymer and cell detachment upon cooling below T(T). This Article presents an alternative, thermoresponsive polymer platform that is based on 2-(2-methoxyethoxy)ethyl methacrylate (MEO2MA) containing copolymer brushes prepared via surface-initiated atom transfer radical polymerization (SI-ATRP). These brushes are interesting as they gradually collapse and dehydrate upon increasing the temperature from 10 to 40 °C, yet resist nonspecific adhesion of cells over this entire temperature window. The MEO2MA based brushes presented here were modified via a two-step postpolymerization modification protocol to introduce cell-adhesive RGD containing peptide ligands. The possibility to reversibly control the swelling and collapse of these brush films by varying temperature allows to modulate the effectively available surface concentration of these cell-adhesive cues and thus provides a way to mask/unmask their biological activity. As a first proof of concept, this Article demonstrates that these MEO2MA brush copolymer films enable integrin-mediated adhesion of 3T3 fibroblasts at 37 °C and allow release of these cells by cooling to 23 °C. The use of cell-adhesive ligands, which can be thermoreversibly masked/unmasked, is attractive as it enables the use of serum-free cell culture conditions. This is advantageous since it avoids possible concerns regarding eventual toxicity and immunological side effects of serum proteins and also provides opportunities to select for particular cell types and for enhanced control over cell stimulation and differentiation.

Poly(2-hydroxyethyl methacrylate) (PHEMA) and poly(poly(ethylene glycol) methacrylate) (PPEGMA) brushes represent a class of thin, surface-tethered polymer films that have been extensively used e.g. to generate non-biofouling surfaces or as model systems to study fundamental biointerfacial questions related to cell− surface interactions. As the properties of PHEMA and PPEGMA brushes depend on the hydration and swelling of these thin films, it is important to understand the influence of basic structural parameters such as the composition of the polymer brush, the film thickness, or grafting density on these phenomena. This article reports results of a series of experiments that were performed to investigate the swelling behavior and mechanical properties of a diverse library of PHEMA and PPEGMA brushes covering a range of film thicknesses and grafting densities. The swelling ratios of the PHEMA and PPEGMA brushes were determined by ellipsometry and neutron reflectivity experiments and ranged from ∼1.5 to ∼5.0. Decreasing the grafting density and decreasing the film thickness generally results in an increase in the swelling ratio. Modification of the PHEMA and PPEGMA brushes with the cell adhesive RGD peptide ligand was found to result in a decrease in the swelling ratio. The neutron reflectivity experiments further revealed that solvated PHEMA and PPEGMA brushes are best described by a two-layer model, consisting of a polymer-rich layer close to the substrate and a second layer that is swollen to a much higher degree at the brush−water interface.

Surface-grafting thermoresponsive polymers allows the preparation of thin polymer brush coatings with surface properties that can be manipulated by variation of temperature. In most instances, thermoresponsive polymer brushes are produced using polymers that dehydrate and collapse above a certain temperature. This report presents the preparation and properties of polymer brushes that show thermoresponsive surface properties, yet are shape-persistent in that they do not undergo main chain collapse. The polymer brushes presented here are obtained via vapor deposition surfaceinitiated ring-opening polymerization (SI-ROP) of γ-dior tri(ethylene glycol)-modified glutamic acid N-carboxyanhydrides.Vapor deposition SI-ROP of γ-dior tri(ethylene glycol)-modified L-or D-glutamic acid N-carboxyanhydrides affords helical surface-tethered polymer chains that do not show any changes in secondary structure between 10 and 70 °C. QCM-D experiments, however, revealed significant dehydration of poly(γ-(2-(2-methoxyethoxy)ethyl)-L-glutamate) (poly(L-EG 2 -Glu)) brushes upon heating from 10 to 40 °C. At the same time, AFM and ellipsometry studies did not reveal significant variations in film thickness over this temperature range, which is consistent with the shape-persistent nature of these polypeptide brushes and indicates that the thermoresponsiveness of the films is primarily due to hydration and dehydration of the oligo(ethylene glycol) side chains. The results presented here illustrate the potential of surface-initiated NCA ring-opening polymerization to generate densely grafted assemblies of polymer chains that possess well-defined secondary structures and tunable surface properties. These polypeptide brushes complement their conformationally unordered counterparts that can be generated via surface-initiated polymerization of vinyl-type monomers and represent another step forward to biomimetic surfaces and interfaces.

No abstract