Cold-formed steel (CFS) construction is widely recognised as an important contributor to sustainability and green construction. Thus, the use of CFS construction is encouraged and had been advanced by innovations in its structural applications. One such innovation that has recently gained popularity is the use of CFS sections in composite construction. The researchers assembled two CFS Clipped channels back to back to construct Ibeam sections for testing. Innovative bracket shear connectors were also developed and inserted between concrete slabs and steel beams in order to provide composite action. The composite beams were drastically stronger and stiffer than non-composite beams. The experimental results were validated theoretically with a high level of correspondence. The proposed composite beams with CFS sections were found to be strong and stiff enough to be used in the construction industry.
In urban environments, vegetation has largely been replaced by impervious and often dark surfaces. These conditions contribute to an Urban Heat Island (UHI) effect. This phenomenon is demonstrated in many cities and produced effects such as higher atmospheric temperatures, intensive precipitation, excessive solar radiation and increasing air pollution. Therefore, reducing the surface temperature of roofs in a building may play an important role in improving the conventional roof surfaces with green roofs that offer much lower temperatures throughout a day to reach their thermal performance and reduce the absorption of solar radiation. Thus, this study is focused on determining the effectiveness of the existing green roof in reducing the ambient temperature and humidity of the air above it by comparison with conventional open roof top without vegetation. This study also aims to evaluate the potential of green roof to reduce the air pollutants in improving air quality in urban cities. As a result, by adopting green roof system, it has reduced temperature during the hottest hour in a day at 1230 hour (hr) by 4.3°C when compared to open roof. Green roof has also recorded higher percentage of humidity compared to open roof. Most importantly, it was proven through this study that green roof has the potential of absorbing pollutants in the air by reducing the concentrations of Sulphur dioxide (SO2), Ammonia (NH3), Nitrogen dioxide (NO2), Ozone (O3) and Carbon monoxide (CO) compared to open roof. Thus, green roofs can be considered to be one of the effective methods to mitigate UHI effects in urban cities.
The aim of this study was to investigate the feasibility of using nonmetallic printed circuit board (PCB) waste as filler in recycled HDPE (rHDPE) in production of rHDPE/PCB composites. Maleic anhydride modified linear low-density polyethylene (MAPE) was used as compatibilizer. In particular, the effects of nonmetallic PCB and MAPE on mechanical properties of the composites were assessed through tensile, flexural and impact testing. Scanning electron microscope (SEM) was used to study the dispersion of nonmetallic PCB and MAPE in the matrix. Nonmetallic PCB was blended with rHDPE from 0–30 wt% and prepared by counter-rotating twin screw extruder followed by molding into test samples via hot press for analysis. A good balance between stiffness, strength and toughness was achieved for the system containing 30 wt% PCB. Thus, this system was chosen in order to investigate the effect of the compatibilizer on the mechanical properties of the composites. The results indicate that MAPE as a compatiblizer can effectively promote the interfacial adhesion between nonmetallic PCB and rHDPE. The addition of 6 phr MAPE increased the flexural strength, tensile strength and impact strength by 71%, 98% and 44% respectively compared to the uncompatibilized composites.
Composites based on recycled high density polyethylene (rHDPE) and nonmetallic printed circuit board (PCB) waste were made through melt compounding and compression molding. In this study, the chemical compositions of the nonmetallic PCB material were determined via XRF and it was confirmed that it contains predominantly 72.7% of glass fiber materials which improve the mechanical performances of the rHDPE matrix. The main aim of this study is to determine the effect of different particle sizes and loadings of nonmetallic PCB on mechanical properties of rHDPE/PCB composite. The results indicated that mechanical properties of composites were excellent when nonmetallic materials with particle size from 0.09 to 0.15 mm and adding amount was 30 wt%. Microscopic images revealed that nonmetallic particles with the size of 0.07-0.09 mm and 0.09 -0.15 mm contained majority of single glass fibers whereas, bigger particle sizes of 0.15-0.3 mm and 0.3-0.5 mm, contained glass fibers in the form of bundles and large resin sheet.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.