Mechanochromic polymeric systems are intensively investigated for real-time stress detection applications. However, an effective stress-sensing material must respond to low deformation with a detectable color change that should be quickly reversible upon force unloading. In this work, mechanochromic nanofibers made by electrospinning are used to produce mechanochromic nanofiber/poly(dimethylsiloxane) (PDMS) composites with isotropic and anisoptropic response. Due to chain alignment of spiropyran copolymer chains within the nanofibers, only very small strains are required to yield a mechanochromic response. Composites with aligned and isotropic nanofibers show anisotropic and isotropic mechanochromic behavior, respectively. Due to the special substitution pattern of spiropyran in the copolymer, the mechanochromic response of these nanofiber/PDMS composites shows fast reversibility upon force unloading. The outstanding benefit of using highly sensitive mechanochromic nanofibers as filler in composite materials allows the detection of directional stress and strain, and it is a step forward in the development of smart, mechanically responsive materials.

Pd-catalyzed direct arylation (DA) reaction conditions have been established for unsubstituted furan (Fu) and thiophene (Th) with three popular acceptor building blocks to be used in materials for organic electronics, namely 4,7-dibromo-2,1,3-benzothiadiazole (BTBr2), N,N′-dialkylated 2,6-dibromonaphthalene-1,4,5,8-bis(dicarboximide) (NDIBr2), and 1,4-dibromotetrafluorobenzene (F4Br2). Reactions with BTBr2, F4Br2, and NDIBr2 require different solvents to obtain high yields. The use of dimethylacetamide (DMAc) is essential for the successful coupling of BTBr2 and F4Br2, but detrimental for NDIBr2, as the electron-deficient NDI core is prone to nucleophilic core substitution in DMAc as solvent but not in toluene. NDIFu2 is much more planar compared to NDITh2, resulting in an enhanced charge-transfer character, which makes it an interesting building block for conjugated systems designed for organic electronics. This study highlights direct arylation as a simple and inexpensive method to construct a series of important donor–acceptor–donor building blocks to be further used for the preparation of a variety of conjugated materials.

Naphthalene diimide (NDI) with tertiary amine side chains is used to n-dope NDI derivatives of varying energy levels.

Junction-functionalized donor-acceptor (D-A) block copolymers (BCPs) enable spatial and electronic control over interfacial charge dynamics in excitonic devices such as solar cells. Here we present the design, synthesis, morphology and electronic characterization of block junctionfunctionalized, all-conjugated, all-crystalline D-A BCPs. Poly(3-hexylthiophene) (P3HT), a single thienylated diketopyrrolopyrrole (Th x DPPTh x , x=1 or 2) unit and poly{[N,N'-bis(2octyldodecyl)-naphthalene-1,4,5,8-bis(dicarboximide)-2,6-diyl]-alt-5,5'-(2,2'-bithiophene)} (PNDIT2) is used as donor, interfacial unit and acceptor, respectively. Almost all C-C coupling steps are accomplished by virtue of C-H activation. Synthesis of the macroreagent H-P3HT-Th x DPPTh x , with x determining its C-H reactivity, is key to the synthesis of various BCPs of type H-P3HT-Th x DPPTh x -block-PNDIT2. Remarkable morphological behavior is determined from a combination of calorimetry, transmission electron microscopy (TEM) and thin film scattering. Block copolymer crystallinity of P3HT and PNDIT2 is reduced indicating frustrated crystallization. A long period l p , is invisible from TEM, but shows up in resonant soft X-ray scattering experiments on a length scale of l p ~60 nm. Charge transfer photoluminescence of H-P3HT-Th x DPPTh x indicates efficient transfer of the excitation energy to the DPP chain end, but is quenched in BCP films. Transient absorption and pump-push-photocurrent spectroscopies reveal geminate recombination (GR) as the main loss channel in as-prepared BCP films independent of junction functionalization. Melt-annealing increases GR as a result of the low degree of crystallinity and poorly defined interfaces, and additionally changes backbone orientation of PNDIT2 from face-on to edge-on. These morphological effects dominate solar cell performance and cause an insensitivity to the presence of the block junction.

This work reports on the isomerisation behaviour of alkylated spiropyrans and aliphatic main chain spiropyran copolymers.

Doped organic semiconductors are required for applications such as organic solar cells, organic light-emitting diodes and thermoelectric generators. To further establish structure-property relationships and improve the efficiency of these devices, electron acceptor conjugated polymers and suitable doping schemes are required. A key criterion is a sufficiently low lowest unoccupied molecular orbital (LUMO), which enables air-stability of excess electrons. In this work, a series of naphthalene diimide (NDI) copolymers with varying highest occupied molecular orbital (HOMO) and LUMO energy levels are made and used to investigate photochemically and thermally induced electron transfer from a small molecule NDI carrying dimethylaminopropyl (DMAP) side chains. Density functional theory calculations, UV-vis and electron spin resonance (ESR) spectroscopies indicate that the LUMO energy level of the NDI copolymer governs thermal electron transfer from the HOMO of the DMAP side chain and dictates air stability of the corresponding radical anions. Conversely, photoinduced electron transfer from DMAP to the NDI copolymer is governed by the position of the HOMO energy levels. While dicyano-substituted NDI copolymers with very low LUMO levels display the highest radical anion yield and excellent air stability, their conductivity is limited by electron mobility, which in turn is strongly influenced by backbone torsion and localized radical anions. These results establish fundamental structure-function relationships and shine light on the use of simple and cost-economic, covalently bound tertiary amines as potential n-dopants for electron acceptor copolymers.

A series of defect-free n-type copolymers poly(naphthalene diimide-alt-indacenodithiophene) P(NDI-IDT) comprising alternating naphthalene diimide (NDI) and indacenodithiophene (IDT) units is prepared using atom-economic direct arylation polycondensation (DAP). Copolymers with varying molecular...

No abstract