No abstract

The production of biofuels from renewable sources is a major challenge in research. Methanol, ethanol, dimethyl ether (DME), synthetic natural gas (SNG), and hydrogen can be produced from syngas which is the result of the gasification of biomasses. Syngas composition varies according to the gasification technology used (such as fixed bed reactors, fluidized bed reactors, entrained flow reactors), the feedstock characteristics, and the operating parameters. This paper presents a review of the predominant biomass gasification technologies and biofuels obtained from syngas by biomass gasification.

The exploration of new food sources and natural products is the result of the increase in world population as well as the need for a healthier diet; in this context, microalgae are undoubtedly an interesting solution. With the intent to enhance their value in new commercial applications, this paper aims to characterize microalgae that have already been recognized as safe or authorized as additives for humans and animals (Chlorella vulgaris, Arthrospira platensis, Haematococcus pluvialis, Dunaliella salina) as well as those that have not yet been marketed (Scenedesmus almeriensis and Nannocholoropsis sp.). In this scope, the content of proteins, carbohydrates, lipids, total dietary fiber, humidity, ash, and carotenoids has been measured via standard methods. In addition, individual carotenoids (beta-carotene, astaxanthin, and lutein) as well as individual saturated, monounsaturated, and polyunsaturated fatty acids have been identified and quantified chromatographically. The results confirm the prerogative of some species to produce certain products such as carotenoids, polyunsaturated fatty acids, and proteins, but also show how their cellular content is rich and diverse. H. pluvialis green and red phases, and Nannochloropsis sp., in addition to producing astaxanthin and omega-3, contain about 25–33% w/w proteins on a dry basis. D. salina is rich in beta-carotene (3.45% w/w on a dry basis), S. Almeriensis is a source of lutein (0.30% w/w on a dry basis), and the C. vulgaris species is a protein-based microalgae (45% w/w on a dry basis). All, however, can also produce important fatty acids such as palmitic acid, γ-linolenic acid, and oleic acid. Considering their varied composition, these microalgae can find applications in multiple sectors. This is true for microalgae already on the market as well as for promising new sources of bioproducts such as S. almeriensis and Nannochloropsis sp.

Solvent Extraction was tested to extract astaxanthin from Haematococcus pluvialis in red phase (HPR), by investigating effects of solvents, extraction pressure and temperature. Astaxanthin isomers were identified and quantified in the extract. The performances of acetone and ethanol, Generally Recognized As Safe (GRAS) solvents, were explored. Negligible effect of pressure was found, while with increasing extraction temperature astaxanthin recovery increased till a maximum value, beyond which thermal degradation seemed to be greater than the positive effect of temperature on extraction. Furthermore, to maximize the extraction yield of astaxanthin, mechanical pre-treatment of HPR biomass was carried out and several extraction runs were consecutively performed. Experimental results showed that after the mechanical pre-treatment the astaxanthin recovery strongly increased while a single extraction run of 20 min was sufficient to extract more than 99% of total astaxanthin extracted. After pre-treatment, maximum recovery of about 87% was found for acetone (pressure = 100 bar; temperature = 40 °C; total time = 60 min).

Haematococcus pluvialis microalgae in the red phase can produce significant amounts of astaxanthin, lutein, and fatty acids (FAs), which are valuable antioxidants in nutraceutics and cosmetics. Extraction of astaxanthin, lutein, and FAs from disrupted biomass of the H. pluvialis red phase using carbon dioxide (CO2) in supercritical fluid extraction (SFE) conditions was investigated using a bench-scale reactor in a semi-batch configuration. In particular, the effect of extraction time (20, 40, 60, 80, and 120 min), CO2 flow rate (3.62 and 14.48 g/min) temperature (50, 65, and 80 °C), and pressure (100, 400, and 550 bar.) was explored. The results show the maximum recovery of astaxanthin and lutein achieved were 98.6% and 52.3%, respectively, at 50 °C and 550 bars, while the maximum recovery of FAs attained was 93.2% at 65 °C and 550 bars.