This article summarizes the results of a research study that was focused on the possibility of removing Cr (VI) from aqueous solution, using low-cost waste biomaterial in a batch mode. A set of seven biosorbents was used: Fomitopsis pinicola, a mixture of cones, peach stones, apricot stones, Juglans regia shells, orange peels, and Merino sheep wool. Three grain fractions (fr. 1/2, fr. 0.5/1.0, and fr. 0/0.5 mm) of biosorbents were studied. The aim was to find the most suitable biosorbent that can be tested with real samples. The influence of other factors on the course of biosorption was studied as well (chemical activation of the biosorbent, pH value, rotation speed during mixing, temperature, and the influence of biosorbent concentration). The use of chemical activation and adjustment of the pH to 1.1 to 2.0 make it possible to increase their sorption capacity and, for some biosorbents, to shorten the exposure times. Two kinetic models were used for the analysis of the experimental data, to explain the mechanism of adsorption and its possible speed control steps: pseudo-first and pseudo-second-order. The pseudo-second-order kinetic model seems to be the most suitable for the description of the experimental data. The thermodynamic parameters suggest that the biosorption was endothermic and spontaneous. In the biosorption equilibrium study, the adsorption data were described by using Langmuir and Freundlich adsorption isotherms. The Langmuir model was applicable to describe the adsorption data of all biosorbents. Both models are suitable for chemically treated sheep fleece and peach stones.

This article deals with the possibility of using a biosorbent in the form of a mixture of cones from coniferous trees to remove the residual concentration of hazardous metals contained in hazardous waste, which is disposed of in a neutralization station. The efficiency of the tested biosorbent in removing Ni, Zn, Cu, and Fe was monitored here. Laboratory research was carried out before the actual testing of the biosorbent directly in the operation of the neutralization station. With regard to the planned use of the biosorbent in the operational test, the laboratory experiments were performed in a batch mode and for the most problematic metals (Ni and Zn). The laboratory tests with real wastewater have shown that the biosorbent can be used to remove hazardous metals. Under the given conditions, 96% of Ni and 19% of Zn were removed after 20 min when using NaOH activated biosorbent with the concentration of 0.1 mol L−1. The inactivated biosorbent removed 93% of Ni and 31% of Zn. The tested biosorbent was also successful during the operational tests. The inactivated biosorbent was applied due to the financial costs. It was used for the pre-treatment of hazardous waste in a preparation tank, where a significant reduction in the concentration of hazardous metals occurred, but the values of Ni, Cu, and Zn still failed to meet the emission limits. After 72 h, we measured 10 mg L−1 from the original 4,056 mg L−1 of Ni, 1 mg L−1 from the original 2,252 mg L−1 of Cu, 1 mg L−1 from the original 4,020 mg L–1 of Zn, and 7 mg L−1 from the original 1,853 mg L−1 of Fe. However, even after neutralization, the treated water did not meet the emission limits for discharging into the sewer system. The biosorbent was, therefore, used in the filtration unit as well, which was placed in front of the Parshall flume. After passing through the filtration unit, the concentrations of all the monitored parameters were reduced to a minimum, and the values met the prescribed emission limits. The biosorbent was further used to thicken the residual sludge in the waste pre-treatment tank, which contributed to a significant reduction in the overall cost of disposing of residual hazardous waste. This waste was converted from liquid to solid-state.

No abstract

The tailings are significant geological environments in mining and industrial regions. They represent special engineering-geological zones of anthropogenic sediments that require specific engineering-geological investigation. In particular, it is important to examine the sites in detail with regard to their potential heterogeneity. The article deals with an important engineering-geological issue of burning in coal mine and coal tailing dumps. A case study was implemented in a tailing dump in Heřma-nice located in Ostrava which is a major industrial city of the Czech Republic. In this urban agglomeration, anthropogenic sediments form 20 % of all foundation soils. Thermometric monitoring in Heřmanice detected a thermally active coal tailing dump with burning as deep as 9 m. The burning is predominantly related to the content of oxygen in the body of the tailing. It belongs to the limiting conditions of the pyrophoric and consequently self-sustained burning. Other factors are sufficient contents and quality of coal mass and capacity to accumulate thermal energy of exothermal reactions. Dynamics of changes in the burning processes were identified in dependence on time, depth and distribution. There was a considerable heterogeneity of thermal activity as for all parameters, and changes were observed from the point of view of time. Considering the depth, burning gradually spread deeper. However, in the depth of 12 m, no significant thermal activity was observed within the overall studied locality. It may be stated that thermal activity is observed as much as 40 % of the studied area. Directionally, there was a progression of the process from west to east. The identified facts may be applied in final designed levels of coal tailing dumps where observational experiences identified intense cooling up to the height of 5 m preventing higher stages of self-ignition process (best situation). Tailing dumps from 5 to 12 m may already be thermally active (meeting other boundary conditions), and in tailing dumps over 12 m, it is clear that there is no thermal activity below 12 m.

This article describes an experimental study aimed at investigating the potential use of recycled rubber granulate from waste tires of fractions 0/1 and 1/3 mm in cement composites as a 100% replacement for natural aggregates. The use of waste in the development and production of new building materials represents an important aspect for the sustainability and protection of the environment. This article is focused on the sound-absorbing and thermal-insulating properties of experimental cement composites based on recycled rubber from waste tires. The article describes the grain characteristics of recycled rubber, sound absorption capacity, thermal conductivity and strength characteristics. The results of this research show that the total replacement of natural aggregate with recycled rubber in cement composites is possible. Replacing natural aggregate with recycled rubber has significantly improved the thermal and acoustic properties of the prepared cement composites, however, at the same time; there was also the expected decrease in the strength characteristics due to the elasticity of rubber.