Abstract:Concrete is a very popular material in the construction industry-it is, however, susceptible to quasi-brittle failure and restricted energy absorption after yielding. The incorporation of short discrete fibers has shown great promise in addressing these shortfalls. A natural fiber such as sisal is renewable, cheap, and easily available. It has also exhibited good tensile strength and can significantly improve the performance of concrete. In this study, the physical and mechanical properties of sisal fiber-reinforced concrete were reported. Sisal fibers were added in the mix at percentages of 0.5%, 1.0%, 1.5%, and 2.0% by weight of cement. Physical properties measured are workability, water absorption, and density while mechanical properties reported are compression strength, split tensile strength, and static modulus of elasticity. The computed modulus of elasticity of sisal fiber-reinforced concrete was compared with predicted values in some common design codes. From the study, it was concluded that sisal fiber can enhance the split tensile strength and Young's modulus of concrete but cannot improve its workability, water absorption, and compressive strength.
Introduction: Fiber reinforced concrete is becoming popular in improving the quasi-brittle failure of concrete. Natural fibers such as sisal holds great promise in this regard. It has amazing tensile strength and is renewable. This paper presents the result of an investigation carried out on the effect of sisal fiber on the compressive strength, Split tensile strength, failure mode and Poisson ratio of Sisal Fiber-Reinforced Concrete (SFRC). Methods: A mix proportion of 1:1.92:3.68 and w/c ratio of 0.47 for a target compressive strength of 35 MPa was used. Sisal fiber was added at percentages of 0.5%, 1.0%, 1.5%, and 2.0% by weight of cement. The effect of specimen shape on the compressive strength of sisal fiber-reinforced concrete (SFRC) was reported. The compressive strength of cube (150mm X 150mm) and cylinder (150mm diameter and 300mm height) specimen was determined at 7 and 28 days, while Split tensile strength and Poisson ratio were obtained using cylindrical specimen (150mm diameter and 300mm height). Results and Conclusion: The result shows that the addition of sisal fiber slightly reduces the compressive strength of concrete, increases its split tensile strength up to 47.167% of the control specimen, arrests crack propagation and reduces its Poisson ratio. The correlation between the compressive strength of cylindrical and cube specimen was established with a ratio ranging between 0.82 - 0.73. The difference in the compressive strength was found to increase with rise in the percentages of sisal fiber. Based on the ratio and mechanical properties, 1.0% sisal fiber content was recommended as the optimum for reinforcing concrete.
Background: In recent decades, the enduring interest and continued development of straw bale as a walling material are based on its beneficial properties. Straw bale is a biomaterial that contributes greatly to carbon footprint reduction and offers excellent thermal insulation. It is proved that plastered straw bale assemblies have good mechanical properties and can be used for the construction of a single storey building. It is known that straw bale presents high displacement in the assemblies; thus, pre-compression is a major step that helps to push down straw bale so as to avoid future structural failure in the wall. There is no clue yet if this method is structurally beneficial than to stabilized single straw bales before assembling them into a structural panel. Objective: This paper presents the structural performance of straw block assemblies under compression loads. Method: Straw blocks and mortar were used to construct plastered and un-plastered wall panels, which were tested under uniformly distributed compression load till failure. Results: The results obtained show that plastered straw block assemblies can support at least 286 KN/m2, which is higher than the minimum slab load 18.25KN/m2, including imposed load for a residential house. In addition, the strength of plastered straw block assemblies plastered with cement-gum mortar, 0.3 N/ mm2 is greater than the strength of a single storey building (0.19N/mm2). Furthermore, results indicate that un-plastered and plastered straw block assemblies perform better than un-plastered and plastered straw bale assemblies. Plastered straw block assemblies support up to 52KN while plastered straw bale assemblies support only 41.1KN. Conclusion: Under compression load, straw block assemblies have a load carrying capacity greater than the minimum slab load. Therefore, Straw block can be used for the construction of a single storey building.
A method is described for comparing the strength of the material near the inner and outer surfaces of the eggshell of the domestic fowl. Half eggs with blunt poles, obtained by cutting the egg around the equator, were subjected to concentric loading through neoprene O-rings, respectively 7 mm and 15.5 mm diameter. A finite element solution for the stress distribution showed that the point of maximum tensile stress lay on the line of the smaller ring. For downward loading on the smaller ring, the maximum stress occurred on the inner surface of the shell. For upward loading it moved to the outer surface. Upward loading gave a value for the average fracture stress of the outer surface of the shell (27.3 Nmm-2). For downward loading fracture occurred on the outer surface at the larger ring before the fracture stress was reached on the inner surface. This measurement gave a lower bound to the average fracture stress of the inner surface (30.4 Nmm-2). The fracture stress of the inner surface was measured using concentric loading along the axis of the whole egg. The average fracture stress was 36.7 Nmm-2 so the inner surface is 34% stronger than the outer surface.
The characteristics of concrete are influenced by the ratio of water to cementitious materials (w/c) used in the mixture. An increase in paste quality will yield higher compressive and flexural strength, lower permeability, increased resistance to weathering, improve the bond between concrete and reinforcement, reduced volume change from drying and wetting, and reduced shrinkage cracking tendencies. Admixtures are used to improve the properties of concrete or mortar. The current study investigates the effect of Sisal Juice Extract (SJE) as an admixture on concrete durability. SJE contains unrefined minerals which can be used as organic retarders to increase the rate of strength development at an early age. A total of 84 concrete cubes were produced in 7 sets of 12 samples each. One set was the control mix which had zero SJE content. The remaining sets had varying dosages of SJ namely 5%, 10%, 15%, 20%, 25%, and 30%. Twelve beam specimens were also cast and subjected to the three-point flexural test. To establish the effect on strength of concrete, compressive strength was tested at 7, 14, 28, and 56 days while flexural strength was tested at 28 days. The highest compressive strength was achieved at 5% dosage beyond which a decrease in strength occurred for all the higher dosages.
Bond strength and critical penetration depth of rust are major factors that affect the service life of reinforced concrete structures. This research endevoured to establish a relationship between the bond strength and critical penetration depth of rust for reinforced concrete structures. There are 7 brands of Cem 1 cement in Kenya available for use in concrete structures. To achieve the desired objective, three Cem 1 cement brands (Cem A, B and C), fine aggregates, coarse aggregates and steel were obtained from the local Kenyan market. The chemical and physical properties of the materials were investigated. For a selected design strength of 25N/mm2, concrete materials were batched by weight and mixed by an electric pan mixer. For each brand of cement 9 cubes of size 150mm * 150mm * 150mm for a compression test, 9 cylinders of 150mm * 300mm for tensile strength and 9 cylinders of 150mm * 300mm for bond strength were cast. After 24 hours, the cast specimens were demoulded and immersed in curing tanks for 27 days. Specimens for compression, split tensile and bond strength were tested at 7,14 and 28 days. From the results, it was observed that the chemical composition of Cem 1 brands in the Kenyan market vary, which affects the hardening properties of concrete. A model for the critical penetration depth of rust in reinforced concrete was proposed by establishing a correlation between the spilt tensile and bond strength and substituting it in the Xu and Shayan model. The proposed and published models compared well. From the proposed model, a relationship between the critical penetration depth and bond strength was established. It was noted that the critical penetration depth increased with an increase in the bond strength of reinforced concrete. The results of this research are expected to contribute to the modeling of the service life of reinforced concrete structures.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with đź’™ for researchers
Part of the Research Solutions Family.