Recently, intensive studies on the role of water molecule in the formation of organic–inorganic perovskite film have been reported. However, not only the contradictive phenomena but also the complex processing technique has hindered the widespread use of water molecule in perovskite preparation. Here the hydration water is introduced into the precursors instead of water. By precisely controlling the content of hydration water, a smoother and more uniform perovskite film is obtained through a simple one‐step spin coating method. The improvement of perovskite film quality leads to highly efficient planar perovskite solar cells. Summing up the device studies and the investigation of morphology, crystallization, and optical properties, the impact of water molecule in the formation of perovskite crystal and consequences of device performance is understood. Due to its universal adaptability and simplified process, precise control of hydration water is therefore of great utility to high quality perovskite films fabrication and large‐scale production of this upcoming photovoltaic technology.
With the assistance of a ferroelectric field created by a ferroelectric polymer, the performance of perovskite photo transistors is significantly improved.
Recently, perovskite based solar cells have attracted lots of research interest, some of which is in the passivation of perovskite surfaces, particularly the heterojunction based surface passivation. In this study, the optical dynamics of MAPbBr single crystals with and without heterojunction passivation were studied systematically by means of a time-resolved spectroscopic technique for the first time. The emission lifetime of MAPbBr single crystals under two-photon (1064 nm) excitation is a few orders of magnitude longer than that measured under one-photon (355 nm or 532 nm) excitation. Interestingly, with surface passivation, the lifetime measured at 355 nm excitations could be tuned significantly, whereas the lifetime change under 1064 nm excitations was considerably less. Our results give a direct evidence of surface quench by comparing the lifetimes before and after surface passivation. Furthermore, the results demonstrate that proper MAPbCl-MAPbBr heterojunctions can dramatically reduce the recombination channels in the surface region, which can be potentially useful for perovskite based solar cells, light emitting diodes (LED), and sensitive detectors.
The flexible electronics has been deemed to be a promising approach to the wearable electronic systems. However, the mismatching between the existing flexible deices and the conventional computing paradigm results an impasse in this field. In this work, a new way to access to this goal is proposed by combining flexible devices and the neuromorphic architecture together. To achieve that, a high-performance flexible artificial synapse is created based on a carefully designed and optimized memristive transistor. The device exhibits high-performance which has near-linear non-volatile resistance change under 10,000 identical pulse signals within the 515% dynamic range, and has the energy consumption as low as 45 fJ per pulse. It also displays multiple synaptic plasticity features, which demonstrates its potential for real-time online learning. Besides, the adaptability by virtue of its threeterminal structure specifically contributes its improved uniformity, repeatability, and reduced power consumption. This work offers a very viable solution for the future wearable computing.
One-step solution process is the simplest method to fabricate organic-inorganic metal halide perovskite thin films, which however does not work well when employed in the planar-heterojunction (PHJ) solar cells due to the generally poor film morphology. Here we show that hydrazinium chloride can be used as an additive in the precursor solution to produce perovskite films featuring higher coverage and better crystallinity. The light absorption ability and charge carrier lifetime are both significantly improved accordingly. Under the optimal additive ratio, the average power conversion efficiency (PCE) of the inverted PHJ perovskite solar cells greatly increases by as much as 70%, and the champion device shows a satisfying PCE of 12.66%. These results suggest that NHCl is a promising additive for fabricating high-efficiency perovskite solar cells via one-step method, which could be of interest in the future commercial solar cell industry.
Aerosol jet printing technology enables fine feature deposition of electronic materials onto low-temperature, non-planar substrates without masks. In this work, silver nanowires (AgNWs) are proposed to be printed into transparent flexible electrodes using a Maskless Mesoscale Material Deposition Aerosol Jet® printing system on a glass substrate. The influence of the most significant process parameters, including printing cycles, printing speed, and nozzle size, on the performance of AgNW electrodes was systematically studied. The morphologies of printed patterns were characterized by scanning electron microscopy, and the transmittance was evaluated using an ultraviolet-visible spectrophotometer. Under optimum conditions, high transparent AgNW electrodes with a sheet resistance of 57.68 Ω/sq and a linewidth of 50.9 μm were obtained, which is an important step towards a higher performance goal for flexible electronic applications.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.