The solar steam process, akin to the natural water cycle, is considered to be an attractive approach to address water scarcity issues globally. However, water extraction from groundwater, for example, has not been demonstrated using these existing technologies. Additionally, there are major unaddressed challenges in extracting potable water from seawater including salt accumulation and long-term evaporation stability, which warrant further investigation. Herein, a high-performance solar steam device composed entirely of natural wood is reported. The pristine, natural wood is cut along the transverse direction and the top surface is carbonized to create a unique bilayer structure. This tree-inspired design offers distinct advantages for water extraction, including rapid water transport and evaporation in the mesoporous wood, high light absorption (≈99%) within the surface carbonized open wood channels, a low thermal conductivity to avoid thermal loss, and cost effectiveness. The device also exhibits long-term stability in seawater without salt accumulation as well as high performance for underground water extraction. The tree-inspired design offers an inexpensive and scalable solar energy harvesting and steam generation technology that can provide clean water globally, especially for rural or remote areas where water is not only scarce but also limited by water extraction materials and methods.

A bimodal porous evaporator is developed for efficient, stable, and salt-rejecting desalination of seawater and high-concentration brines.

No abstract

Liquid drops on soft solids generate strong deformations below the contact line, resulting from a balance of capillary and elastic forces. The movement of these drops may cause strong, potentially singular dissipation in the soft solid. Here we show that a drop on a soft substrate moves by surfing a ridge: the initially flat solid surface is deformed into a sharp ridge whose orientation angle depends on the contact line velocity. We measure this angle for water on a silicone gel and develop a theory based on the substrate rheology. We quantitatively recover the dynamic contact angle and provide a mechanism for stick–slip motion when a drop is forced strongly: the contact line depins and slides down the wetting ridge, forming a new one after a transient. We anticipate that our theory will have implications in problems such as self-organization of cell tissues or the design of capillarity-based microrheometers.

All-in-one wood-based solar steam generation devices were prepared by directly carbonizing the top surface of natural wood materials. High solar steam generation efficiencies were achieved by virtue of the excellent hydrophilicity, low thermal conductivity, interconnected porous network, and improved light absorption capability, demonstrating the great potential of natural wood in energy-water nexus applications.

Wood, an earth-abundant material, is widely used in our everyday life. With its mesoporous structure, natural wood is comprised of numerous long, partially aligned channels (lumens) as well as nanochannels that stretch along its growth direction. This wood mesostructure is suitable for a range of emerging applications, especially as a membrane/separation material. Here, we report a mesoporous, three-dimensional (3D) wood membrane decorated with palladium nanoparticles (Pd NPs/wood membrane) for efficient wastewater treatment. The 3D Pd NPs/wood membrane possesses the following advantages: (1) the uniformly distributed lignin within the wood mesostructure can effectively reduce Pd(II) ions to Pd NPs; (2) cellulose, with its abundant hydroxyl groups, can immobilize Pd NPs; (3) the partially aligned mesoporous wood channels as well as their inner ingenious microstructures increase the likelihood of wastewater contacting Pd NPs decorating the wood surface; (4) the long, Pd NP-decorated channels facilitate bulk treatment as water flows through the entire mesoporous wood membrane. As a proof of concept, we demonstrated the use and efficiency of a Pd NPs/wood membrane to remove methylene blue (MB, CHNClS) from a flowing aqueous solution. The turnover frequency of the Pd NPs/wood membrane, ∼2.02 mol·mol·min, is much higher than the values reported in the literature. The water treatment rate of the 3D Pd NPs/wood membrane can reach 1 × 10 L·m·h with a high MB removal efficiency (>99.8%). The 3D mesoporous wood membrane with partially aligned channels exhibits promising results for wastewater treatment and is applicable for an even wider range of separation applications.

Solar steam generation, combining the most abundant resources of solar energy and unpurified water, has been regarded as one of the most promising techniques for water purification. Here, an artificial tree with a reverse‐tree design is demonstrated as a cost‐effective, scalable yet highly efficient steam‐generation device. The reverse‐tree design implies that the wood is placed on the water with the tree‐growth direction parallel to the water surface; accordingly, water is transported in a direction perpendicular to what occurs in natural tree. The artificial tree is fabricated by cutting the natural tree along the longitudinal direction followed by surface carbonization (called as C‐L‐Wood). The nature‐made 3D interconnected micro‐/nanochannels enable efficient water transpiration, while the layered channels block the heat effectively. A much lower thermal conductivity (0.11 W m−1 K−1) thus can be achieved, only 1/3 of that of the horizontally cut wood. Meanwhile, the carbonized surface can absorb almost all the incident light. The simultaneous optimizations of water transpiration, thermal management, and light absorption results in a high efficiency of 89% at 10 kW m−2, among the highest values in literature. Such wood‐based high‐performance, cost‐effective, scalable steam‐generation device can provide an attractive solution to the pressing global clean water shortage problem.

The contact angle that a liquid drop makes on a soft substrate does not obey the classical Young's relation, since the solid is deformed elastically by the action of the capillary forces. The finite elasticity of the solid also renders the contact angles differently from those predicted by Neumann's law, which applies when the drop is floating on another liquid. Here, we derive an elastocapillary model for contact angles on a soft solid by coupling a mean-field model for the molecular interactions to elasticity. We demonstrate that the limit of a vanishing elastic modulus yields Neumann's law or a variation thereof, depending on the force transmission in the solid surface layer. The change in contact angle from the rigid limit to the soft limit appears when the length scale defined by the ratio of surface tension to elastic modulus γ/E reaches the range of molecular interactions.