We investigated the correlation between the polymer backbone structural regularity and the charge transport properties of poly{[N,N'-bis(2-octyldodecyl)-1,4,5,8-naphthalenediimide-2,6-diyl]-alt-5,5'-(2,2'-bithiophene)} [P(NDI2OD-T2)], a widely studied semiconducting polymer exhibiting high electron mobility and an unconventional micromorphology. To understand the influence of the chemical structure and crystal packing of conventional regioregular P(NDI2OD-T2) [RR-P(NDI2OD-T2)] on the charge transport, the corresponding regioirregular polymer RI-P(NDI2OD-T2) was synthesized. By combining optical, X-ray, and transmission electron microscopy data, we quantitatively characterized the aggregation, crystallization, and backbone orientation of all of the polymer films, which were then correlated to the electron mobilities in electron-only diodes. By carefully selecting the preparation conditions, we were able to obtain RR-P(NDI2OD-T2) films with similar crystalline structure along the three crystallographic axes but with different orientations of the polymer chains with respect to the substrate surface. RI-P(NDI2OD-T2), though exhibiting a rather similar LUMO structure and energy compared with the regioregular counterpart, displayed a very different packing structure characterized by the formation of ordered stacks along the lamellar direction without detectible π-stacking. Vertical electron mobilities were extracted from the space-charge-limited currents in unipolar devices. We demonstrate the anisotropy of the charge transport along the different crystallographic directions and how the mobility depends on π-stacking but is insensitive to the degree or coherence of lamellar stacking. The comparison between the regioregular and regioirregular polymers also shows how the use of large planar functional groups leads to improved charge transport, with mobilities that are less affected by chemical and structural disorder with respect to classic semicrystalline polymers such as poly(3-hexylthiophene).

We report a new p-type semiconducting polymer family based on the thieno[3,4-c]pyrrole-4,6-dione (TPD) building block, which exhibits good processability as well as good mobility and lifetime stability in thin-film transistors (TFTs). TPD homopolymer P1 was synthesized via Yamamoto coupling, whereas copolymers P2-P8 were synthesized via Stille coupling. All of these polymers were characterized by chemical analysis as well as thermal analysis, optical spectroscopy, and cyclic voltammetry. P2-P7 have lower-lying HOMOs than does P3HT by 0.24-0.57 eV, depending on the donor counits, and exhibit large oscillator strengths in the visible region with similar optical band gaps throughout the series (∼1.80 eV). The electron-rich character of the dialkoxybithiophene counits in P8 greatly compresses the band gap, resulting in the lowest E(g)(opt) in the series (1.66 eV), but also raising the HOMO energy to -5.11 eV. Organic thin-film transistor (OTFT) electrical characterization indicates that device performance is very sensitive to the oligothiophene conjugation length, but also to the solubilizing side chain substituents (length, positional pattern). The corresponding thin-film microstructures and morphologies were investigated by XRD and AFM to correlate with the OTFT performance. By strategically varying the oligothiophene donor conjugation length and optimizing the solubilizing side chains, a maximum OTFT hole mobility of ∼0.6 cm(2) V(-1) s(-1) is achieved for P4-based devices. OTFT environmental (storage) and operational (bias) stability in ambient was investigated, and enhanced performance is observed due to the low-lying HOMOs. These results indicate that the TPD is an excellent building block for constructing high-performance polymers for p-type transistor applications due to the excellent processability, substantial hole mobility, and good device stability.

Bithiophene imide (BTI) and benzodithiophene (BDT) copolymers are synthesized for application in organic photovoltaic (OPV) cells. The electron deficiency of the BTI units leads to polymers with a low-lying HOMOs (∼-5.6 eV). Inverted solar cells are fabricated to investigate the OPV performance of the BTI-based polymers and achieve power conversion efficiencies up to 5.5%, with substantial V(oc)s above 0.9 V which are among the highest V(oc)s reported to date for polymer/PCBM solar cells. The results indicate that the BTI is a promising building block for constructing polymer donors for OPV applications.

Soluble conjugated alternating porphyrin-dithienothiophene copolymersssingle-bond linked (I) and triple-bond linked (IIa and IIb)swere synthesized by palladium(0)-catalyzed Stille and Sonagashira coupling reactions, respectively. The thermal, electrochemical, optical, charge transport, and photovoltaic properties of these copolymers were examined; the effect of the triple bond was studied. I exhibits onset decomposition temperature (T d ) of 410°C and glass-transition temperature (T g ) of 180°C, higher than those of IIb (T d , 330°C; T g , 130°C). The absorption spectrum of I in thin film exhibits a sharp Soret band at 450 nm and two weak Q-bands at 563-619 nm, while IIb exhibits a sharp Soret band at 491 nm and a strong Q-band at 760 nm. The emission maxima of I and IIb in solution are located at 642 and 722 nm respectively. IIb is electrochemically active in both the oxidation and reduction regions, while I shows only oxidation peak. The field-effect hole mobilities as high as 2.1 × 10 -4 cm 2 V -1 s -1 were obtained for these copolymers. Polymer solar cells (PSCs) were fabricated based on the blend of the polymers and methanofullerene [6,6]-phenyl C61-butyric acid methyl ester (PCBM). The power conversion efficiency (PCE) of 0.3% was achieved under AM 1.5, 100 mW/cm 2 for the PSC using IIb:PCBM (1:3, w/w) as active layer. The PCE of the PSC based on IIb:PCBM (1:3, w/w) is double that based on I:PCBM (1:2, w/w), consistent with that IIb exhibits stronger Q-band absorption and higher mobility at room temperature.