The Maximum Reservoir Contact (MRC) concept was developed to improve well productivity and sustainability by maximizing the contact area with target reservoirs. MRC is a proven technology for the development of tight/non-economical reservoirs. Completion design for MRC wells plays a vital role in enhancing well deliverability, monitoring and accessibility. MRC technology was put into application to appraise a tight and thin heterogeneous carbonate reservoir in a giant offshore field in Abu Dhabi. Different completion scenarios were simulated to select the best suited completion to achieve enhanced well deliverability, monitoring and accessibility. Heavy casing design with liner and tie-back system was finalized to maximize accessibility and achieve proper isolation behind casing. A special pre-perforated liner was also designed to eliminate the pressure drop across the wellbore. The MRC drain was divided mainly into two sections, blank pipe and pre-perforated liner equipped with swell packers for isolation. Pre-perforated liner was subdivided into compartments for proper flow distribution, accessibility and monitoring. The blank pipe was utilized to isolate the potential gas zone. Fractures and faults presented a major challenge in achieving the well objective. Special logging requirements were also considered for proper characterization of the suspected faults/fractures as well as to confirm and locate the source of gas risk for compartmentalization. For proper accessibility, monitoring, stimulation and sustainable production, tapered upper completion was designed and equipped with permanent downhole gauge for continuous monitoring. The well was successfully drilled and completed with production performance exceeding expectation which will indeed pave the way to apply MRC technology to unlock the all-out potential from undeveloped tight heterogeneous reservoirs within the field.
In a giant, mature UAE offshore field, consisting of complex multi-stacked heterogeneous reservoirs, the western part has been less developed, due to contrasted reservoir properties and low-permeability layers. The development in that part of the field was re-visited, to account for reservoir challenges and surface limitations. The objective was to achieve production mandates, understand reservoir behavior, while minimizing well count and expenditures associated with interventions and surveillance activities. To evaluate this challenging area of the field, a unique multi-lateral well was designed, targeting three distinct reservoirs, and allowing to concurrently produce and understand them in a viable manner. The reservoirs have poor characteristics, with permeability lower than 10 mD, except for the deeper one, which has some high permeability streaks. Accounting for the tight formations, each horizontal leg had to be stimulated efficiently, despite being inaccessible with coiled-tubing. In addition, well production had to be reliably back-allocated to each drain, and meet pre-defined reservoir guidelines. Despite contrasting properties, all three drains had to be produced at reasonable rates, avoiding that one drain would dominate the other two. And finally, enhanced reservoir understanding was required within each drain, with qualitative indication of their flow profile and associated reservoir conformance. The 3-legged multi-lateral oil producer was drilled and completed successfully. In each of the three horizontal laterals, totaling more than 15,000 feet length, drop-off limited-entry ‘Smart Liners’ were installed, to allow bull-heading stimulation. This offered an effective high-volume matrix acidizing method, adapted to the contrasted properties and tight zones encountered along the laterals. The well was equipped with permanent downhole gauges and inflow control valves (ICV's) to dynamically monitor downhole contributions, modulate production from each drain, avoiding well delivery to be dominated by the highest potential reservoir and control unwanted water/gas production to the surface. To complete the picture, chemical in-flow tracers were installed, in the tubing and within each drain, to monitor the laterals’ flow profiles and performance, and measure the individual contribution from each reservoir. This aimed to determine the efficiency of the ‘Smart Liners’ design and proved a cost-effective option to quantify the contribution from the laterals, compared to running regular PLTs. The resulting pilot is the first well in the world to combine a smart completion with three limited entry ‘smart liners’ utilizing drop-off technique and chemical inflow tracers. The pilot well, which behavior is being evaluated over 2021, provides a groundbreaking approach to evaluate and unlock hydrocarbon resources in a poorly developed area of the field, allowing a significant optimization of well count and of associated capital and operating expenditures.
The scope of this paper is to share a field experience with permanent inflow tracer deployment and monitoring of an intelligent multi-lateral well, completed with Smart-Liner (Limited Entry Liner). It will describe what ADNOC Offshore has learnt through inflow tracing clean up surveillance from several restarts and steady state production through inflow modelling interpretation techniques. This passive method of permanent monitoring technology utilizes chemistry and materials expertise to design tracers that release signature responses when they come into contact with either in-situ oil or formation water. The chemical tracer technology enables wireless monitoring capabilities for up to five years. Unique chemical tracers are embedded in porous polymer matrix inside tracer carriers along select locations in the lower completion to correlate where the oil and water is flowing in a production well. Interpreting tracer signals can provide zonal rate information by inducing transients to create tracer signals that are transported by flow to surface and captured in sample bottles for analysis. The measured signals are matched with models through history matching to yield zonal rate estimates. ADNOC Offshore has installed inflow tracers in an intelligent multi-lateral well to monitor laterals’ contributions, to verify new completion technology, and to estimate the flow profile from individual sections of Smart-Liner, run for the first time in the field. The interpretation results have been able to characterize inflow performance without any intervention in the well. Several restart and steady state surveys are planned to understand some key characteristics of the well completion and reveal how the well has changed since it was put on production. This technology will help allocate commingled production to the three laterals. The use of inflow tracers will provide multiple inflow surveys that will reduce operational risk, well site personnel, costs and will improve reservoir management practices. Permanent inflow tracing is expected to change the way production monitoring can be performed, especially in advanced wells where PLTs or Fiber Optic technology cannot access multi-laterals.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.