A new monolithic perovskite/silicon tandem solar cell architecture is proposed based on double-side-textured silicon cells with sub-micrometer pyramids. These pyramids are rough enough to scatter light within silicon nearly as efficiently as large pyramids but smooth enough to solution process a perovskite film. A bladecoated perovskite film planarizes the textured silicon cell. With a textured lightscattering layer added to the top to reduce front-surface reflectance, a monolithic perovskite/silicon tandem cell reaches an efficiency of 26%.

Hybrid organic-inorganic materials for high-efficiency, low-cost photovoltaic devices have seen rapid progress since the introduction of lead based perovskites and solid-state hole transport layers. Although majority of the materials used for perovskite solar cells (PSC) are introduced from dye-sensitized solar cells (DSSCs), the presence of a perovskite capping layer as opposed to a single dye molecule (in DSSCs) changes the interactions between the various layers in perovskite solar cells. 4-tert-Butylpyridine (tBP), commonly used in PSCs, is assumed to function as a charge recombination inhibitor, similar to DSSCs. However, the presence of a perovskite capping layer calls for a re-evaluation of its function in PSCs. Using TEM (transmission electron microscopy), we first confirm the role of tBP as a HTL morphology controller in PSCs. Our observations suggest that tBP significantly improves the uniformity of the HTL and avoids accumulation of Li salt. We also study degradation pathways by using FTIR (Fourier transform infrared spectroscopy) and APT (atom probe tomography) to investigate and visualize in 3-dimensions the moisture content associated with the Li salt. Long-term effects, over 1000 h, due to evaporation of tBP have also been studied. Based on our findings, a PSC failure mechanism associated with the morphological change of the HTL is proposed. tBP, the morphology controller in HTL, plays a key role in this process, and thus this study highlights the need for additive materials with higher boiling points for consistent long-term performance of PSCs.

We propose a spectrum-dependent mechanism for the oxidation of 2,2',7,7'-tetrakis(N,N-di-p-methoxyphenylamine)-9,9'-spirobifluorene (Spiro-OMeTAD) with bis(trifluoromethane)sulfonimide lithium salt (LiTFSI), which is commonly used in perovskite solar cells as the hole transport layer. The perovskite layer plays different roles in the Spiro-OMeTAD oxidization for various spectral ranges. The effect of oxidized Spiro-OMeTAD on the solar cell performance was observed and characterized. With the initial long-wavelength illumination (>450 nm), the charge recombination at the TiO2/Spiro-OMeTAD interface was increased due to the higher amount of the oxidized Spiro-OMeTAD. On the other hand, the increased conductivity of the Spiro-OMeTAD layer and enhanced charge transfer at the Au/Spiro-OMeTAD interface facilitated the solar cell performance.

Atomic layer deposition (ALD) is a commonly used coating technique for lithium ion battery electrodes. Recently, it has been applied to sodium ion battery anode materials. ALD is known to improve the cycling performance, Coulombic efficiency of batteries, and maintain electrode integrity. Here, the electrochemical performance of uncoated P2-NaNiMnO electrodes is compared to that of ALD-coated AlO P2-NaNiMnO electrodes. Given that ALD coatings are in the early stage of development for NIB cathode materials, little is known about how ALD coatings, in particular aluminum oxide (AlO), affect the electrode-electrolyte interface. Therefore, full characterizations of its effects are presented in this work. For the first time, X-ray photoelectron spectroscopy (XPS) is used to elucidate the cathode electrolyte interphase (CEI) on ALD-coated electrodes. It contains less carbonate species and more inorganic species, which allows for fast Na kinetics, resulting in significant increase in Coulombic efficiency and decrease in cathode impedance. The effectiveness of AlO ALD coating is also surprisingly reflected in the enhanced mechanical stability of the particle which prevents particle exfoliation.