Effective skeletal muscle tissue engineering relies on control over the scaffold architecture for providing muscle cells with the required directionality, together with a mechanical property match with the surrounding tissue. Although recent advances in 3D printing fulfill the first requirement, the available synthetic polymers either are too rigid or show unfavorable surface and degradation profiles for the latter. In addition, natural polymers that are generally used as hydrogels lack the required mechanical stability to withstand the forces exerted during muscle contraction. Therefore, one of the most important challenges in the 3D printing of soft and elastic tissues such as skeletal muscle is the limitation of the availability of elastic, durable, and biodegradable biomaterials. Herein, we have synthesized novel, biocompatible and biodegradable, elastomeric, segmented polyurethane and polyurethaneurea (TPU) copolymers which are amenable for 3D printing and show high elasticity, low modulus, controlled biodegradability, and improved wettability, compared to conventional polycaprolactone (PCL) and PCL-based TPUs. The degradation profile of the 3D printed TPU scaffold was in line with the potential tissue integration and scaffold replacement process. Even though TPU attracts macrophages in 2D configuration, its 3D printed form showed limited activated macrophage adhesion and induced muscle-like structure formation by C2C12 mouse myoblasts in vitro, while resulting in a significant increase in muscle regeneration in vivo in a tibialis anterior defect in a rat model. Effective muscle regeneration was confirmed with immunohistochemical assessment as well as evaluation of electrical activity produced by regenerated muscle by EMG analysis and its force generation via a custom-made force transducer. Micro-CT evaluation also revealed production of more muscle-like structures in the case of implantation of cell-laden 3D printed scaffolds. These results demonstrate that matching the tissue properties for a given application via use of tailor-made polymers can substantially contribute to the regenerative outcomes of 3D printed tissue engineering scaffolds.

A key challenge in skeletal muscle tissue engineering is the choice of a proper scaffolding material as it should demonstrate elastic behavior to withstand and support the dynamic loading of the tissue microenvironment while being biodegradable and biocompatible. In this study, we tested the applicability of a novel biodegradable polyurethane (PU) elastomer chain extended with fibrinogen (Fib) to fulfill these requirements. Biodegradable polyurethane-fibrinogen (PU-Fib) elastomers were synthesized by step-wise condensation polymerization. Firstly, PU prepolymer was synthesized and then Fib was integrated into PU prepolymer during the second step of polymerization. The chemical, thermal, viscoelastic, mechanical and biodegradation properties of PU-Fib were characterized. FTIR-ATR spectrum showed amide bands specific to PU and Fib, DSC thermograms showed the suitable integration between the components. Dynamic mechanical analysis revealed Tg and Tα* transitions at 64.5 °C and 38.4 °C, respectively. PU and Fib had shown chemically compatible interactions and when compared to PCL, PU-Fib possessed viscoelastic properties more suitable to the native tissue. PU-Fib films were produced and seeded with C2C12 mouse myoblasts. Uniaxial cyclic stretch was applied to the cell seeded films for 21 d to mimic the native dynamic tissue microenvironment. Cell proliferation, viability and the expression of muscle-specific markers (immunofluorescent staining for myogenin and myosin heavy chain) were assessed. Myoblasts proliferated well on PU-Fib films; aligned parallel along their long edge, and express myogenic markers under biomimetic dynamic culture. It was possible to culture myoblasts with high viability on PU-Fib elastomeric films mimicking native muscle microenvironment.

Synthetic polymers remain to be a major choice for scaffold fabrication due to their structural stability and mechanical strength. However, the lack of functional moieties limits their application for cell-based therapies which necessitate modification and functionalization. Blending synthetic polymers with natural components is a simple and effective way to achieve the desired biological properties for a scaffold. Herein, nanofibrous mats made of polycaprolactone (PCL) and egg white protein (EWP) blend were developed and further evaluated for use as a scaffold for tissue engineering applications. Homogeneous distribution of EWP was achieved throughout the nanofibrous mats, as shown by immunohistochemistry. ATR-FTIR analysis and contact angle measurements have further confirmed the presence of EWP on the surface of the samples. The swelling test showed that PCL/EWP nanofibers have higher water uptake than PCL nanofibrous mats. Also, EWP addition on the nanofibrous mats resulted in an increase in the tensile strength and Young’s modulus of the mats, indicating that the presence of protein can greatly enhance the mechanical properties of the mats. A significantly higher, more uniform, and dispersed cell spreading was observed on days 7 and 14 than that on neat PCL mats, demonstrating the importance of providing the required cues for cell homing by the availability of EWP. Hence, EWP is shown to be a simple and low-cost source for the functionalization of PCL nanofibrous mats. EWP is, therefore, a facile candidate to enhance cellular interactions of synthetic polymers for a wide range of tissue engineering applications.

Skeletal muscle is an electrically and mechanically active tissue that contains highly oriented, densely packed myofibrils. The tissue has self-regeneration capacity upon injury, which is limited in the cases of volumetric muscle loss. Several regenerative therapies have been developed in order to enhance this capacity, as well as to structurally and mechanically support the defect site during regeneration. Among them, biomimetic approaches that recapitulate the native microenvironment of the tissue in terms of parallel-aligned structure and biophysical signals were shown to be effective. In this study, we have developed 3D printed aligned and electrically active scaffolds in which the electrical conductivity was provided by carbonaceous material (CM) derived from algae-based biomass. The synthesis of this conductive and functional CM consisted of eco-friendly synthesis procedure such as pre-carbonization and multi-walled carbon nanotube (MWCNT) catalysis. CM obtained from biomass via hydrothermal carbonization (CM-03) and its ash form (CM-03K) were doped within poly(ɛ-caprolactone) (PCL) matrix and 3D printed to form scaffolds with aligned fibers for structural biomimicry. Scaffolds were seeded with C2C12 mouse myoblasts and subjected to electrical stimulation during the in vitro culture. Enhanced myotube formation was observed in electroactive groups compared to their non-conductive counterparts and it was observed that myotube formation and myotube maturity were significantly increased for CM-03 group after electrical stimulation. The results have therefore showed that the CM obtained from macroalgae biomass is a promising novel source for the production of the electrically conductive scaffolds for skeletal muscle tissue engineering.

In orthopedic surgery, metals are preferred to support or treat damaged bones due to their high mechanical strength. However, the necessity for a second surgery for implant removal after healing creates problems. Therefore, biodegradable metals, especially magnesium (Mg), gained importance, although their extreme susceptibility to galvanic corrosion limits their applications. The focus of this study was to control the corrosion of Mg and enhance its biocompatibility. For this purpose, surfaces of magnesium−calcium (MgCa1) alloys were modified with calcium phosphate (CaP) or CaP doped with zinc (Zn) or gallium (Ga) via microarc oxidation. The effects of surface modifications on physical, chemical, and mechanical properties and corrosion resistance of the alloys were studied using surface profilometry, goniometry, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), nanoindentation, and electrochemical impedance spectroscopy (EIS). The coating thickness was about 5−8 μm, with grain sizes of 43.1 nm for CaP coating and 28.2 and 58.1 nm for Zn-and Ga-doped coatings, respectively. According to EIS measurements, the capacitive response (Y c ) decreased from 11.29 to 8.72 and 0.15 Ω −1 cm −2 s n upon doping with Zn and Ga, respectively. The E corr value, which was −1933 mV for CaP-coated samples, was found significantly electropositive at −275 mV for Ga-doped ones. All samples were cytocompatible according to indirect tests. In vitro culture with Saos-2 cells led to changes in the surface compositions of the alloys. The numbers of cells attached to the Zn-doped (2.6 × 10 4 cells/cm 2 ) and Ga-doped (6.3 × 10 4 cells/cm 2 ) coatings were higher than that on the surface of the undoped coating (1.0 × 10 3 cells/cm 2 ). Decreased corrosivity and enhanced cell affinity of the modified MgCa alloys (CaP coated and Zn and Ga doped, with Ga-doped ones having the greatest positive effect) make them novel and promising candidates as biodegradable metallic implant materials for the treatment of bone damages and other orthopedic applications.

No abstract

The parathyroid glands are localized at the back of the thyroid glands in the cervical region and are responsible for regulation of the calcium level in the blood, through specialized cells that sense Ca2+ and secrete parathyroid hormone (PTH) in response to a decline in its serum level. PTH stimulates the skeleton, kidneys and intestines and controls the level of Ca2+ through specialized activities. Iatrogenic removal of the parathyroid gland, as well as damage to its vascular integrity during cauterization are some of the common complications of thyroid surgery. Therefore, regeneration and/or replacement of malfunctioning parathyroid tissue is required. Tissue engineering is an emerging and promising field for patients with organ failure with recent pioneering clinical applications. The success of tissue engineering strategies depend on the use of proper cells, bioactive factors that stimulate the activities of these cells and scaffolds that are produced to recapitulate the tissue structure and support the function of the engineered tissues. 3D printing is a developing strategy for the production of these scaffolds by providing a delicate control over their structure and properties. In this study, human primary parathyroid cells were successfully isolated and their viability and ability to secrete PTH upon stimulation with different levels of Ca2+ were shown i in vitro. These cells were then seeded onto 3D printed alginate scaffolds with properties that mimicked the native tissue. Cell viability and the ability to secrete PTH upon stimulation were also demonstrated on 3D printed scaffolds. Therefore, functional hormone-active parathyroid tissue substitutes was engineered in vitro through 3D printed hydrogels and autologous cells.