Pedicle screw augmentation with polymethyl methacrylate improves the initial fixation strength and fatigue strength of instrumentation in osteoporotic vertebrae. Pedicle screws augmented using the kyphoplasty technique had significantly greater pullout strength than those augmented with transpedicular augmentation technique and those placed in healthy control vertebrae with no augmentation.

No abstract

The stability provided by both transfacet pedicle screw fixation and traditional pedicle screw fixation was not compromised after repetitive cycling. In this model, transfacet pedicle screw fixation appears equivalent biomechanically to traditional pedicle screw fixation.

Given the finding that the Krackow suture had less gap formation and better preservation of tendon architecture (length and width) compared with the whipstitch, coupled with the finding that ultimate strength is similar with both types of sutures, the Krackow stitch is recommended for tendon reconstruction when these parameters are important.

This article reports the degradation and biological properties of as-drawn Mg-4Zn-1Sr (designated as ZSr41) and pure Mg (P-Mg) wires as bioresorbable intramedullary pins for bone repair. Specifically, their cytocompatibility with bone marrow derived mesenchymal stem cells (BMSCs) and degradation in vitro, and their biological effects on peri-implant tissues and in vivo degradation in rat tibiae were studied. The as-drawn ZSr41 pins showed a significantly faster degradation than P-Mg in vitro and in vivo. The in vivo average daily degradation rates of both ZSr41 and P-Mg intramedullary pins were significantly greater than their respective in vitro degradation rates, likely because the intramedullary site of implantation is highly vascularized for removal of degradation products. Importantly, the concentrations of Mg, Zn, and Sr ions in the BMSC culture in vitro and their concentrations in rat blood in vivo were all lower than their respective therapeutic dosages, i.e., in a safe range. Despite of rapid degradation with a complete resorption time of 8 weeks in vivo, the ZSr41 intramedullary pins showed a significant net bone growth because of stimulatory effects of the metallic ions released. However, proportionally released OH ions and hydrogen gas caused adverse effects on bone marrow cells and resulted in cavities in surrounding bone. Thus, properly engineering the degradation properties of Mg-based implants is critical for harvesting the bioactivities of beneficial metallic ions, while controlling adverse reactions associated with the release of OH ions and hydrogen gas. It is necessary to further optimize the alloy processing conditions and/or modify the surfaces, for example, applying coatings onto the surface, to reduce the degradation rate of ZSr41 wires for skeletal implant applications.

The initial fixation strength of pedicle screws is commonly tested using a standard pull-out test with load applied at a constant rate. This method overlooks the cyclic nature of in situ loading responsible for clinical failure. This study was undertaken to determine the effects of stress relaxation properties at the bone-screw interface on screw fixation strength. Pedicle screws were inserted into calf lumbar vertebrae using a paired testing array. After embedding and mounting in a custom fixture, axial pull-out tests were performed at the rates of 1, 5, and 25 mm/min. For each vertebra, one screw was pulled at a continuous rate. The other screw was pulled at increments of 0.5 mm, at the same rate, with 1000 s pause between increments. Peak load, energy-to-failure, displacement-to-failure, and stiffness were calculated for each screw pull-out test. Two-way ANOVA showed that the standard pullout method yielded significantly higher peak loads (p < 0.05) at faster pull-out rates and higher stiffnesses (p < 0.05) at all rates compared to the stress relaxation pull-out protocol. These results suggest that the stress relaxation properties of bone significantly affect the pull-out behavior of pedicle screws, reducing the peak load and stiffness values observed during testing. This mode of testing may provide a better biomechanical model of screw pull-out failure and a more accurate estimate of initial fixation strength.

Object Minimally invasive pedicle screws inserted vertically (that is, dorsoventrally) through the pedicle, as opposed to the more common coaxial technique, offer potential advantages by minimizing soft-tissue stripping during screw placement. The screws are designed for insertion through a medial starting point with vertical trajectory through the pedicle and into the vertebral body. As such, no lateral dissection beyond the insertion point is necessary. However, the effects of this insertion technique on the screw biomechanical performance over a short- and long-term are unknown. The authors investigated the pullout strength and stiffness of these screws, with or without fatigue cycling, compared with comparably sized, traditional screws placed by coaxial technique. Methods Twenty-one lumbar vertebrae (L-3, L-4, and L-5) were tested. Each pedicle of each vertebra was instrumented with either a traditional, coaxial pedicle screw (Group A), placed through a standard starting point, or a vertically oriented, alternative-design screw (Group B), with a medial starting point and vertical trajectory. The specimens were divided into 2 groups for testing. One group was tested for direct pullout (10 specimens) while the other was subject to pullout after tangential (toggle) cyclic loading (11 specimens). The screws were cycled in displacement control (± 5 mm producing ~ 4-Nm moment) at a rate of 3 Hz for 5000 cycles. Pullout tests were performed at a rate of 1 mm/minute. Results Two-way ANOVA showed that Group B screws with a medial starting point (2541 ± 1090 N for cycled vs 2135 ± 1323 N for noncycled) had significantly higher pullout loads than Group A screws with a standard entry point (1585 ± 766 N for cycled vs 1417 ± 812 N noncycled) (p = 0.001). There was no significant effect of cycling or screw insertion type on pullout stiffness. Tangential stiffness of the Group B screws was significantly less than that of the Group A screws (p = 0.001). The stiffness of both screws in the toe region was significantly affected by cycling (p = 0.001). Conclusions The use of Group B screws inserted through a medial starting point showed greater pullout load than a Group A screw inserted through a standard starting point. The greater pullout strength in Group B screws may be due to screw thread design and increased cortical bone purchase at the medial starting point. Nevertheless, anatomical considerations of the medial starting point, that is, pedicle or lateral vertebral body cortex breach, may limit its application. The medial starting point of the Group B screw was frequently in the facet at the L-3 and L-4 pedicle entry points, which may have clinical importance.

This study proves that transarticular facet screws and lateral mass plates are equivalent in two-level instrumentations of the cervical spine. This is the first biomechanical study to test transarticular facet screws in this context.