Numerical results for an internal ribbed cooling channel including a 180 deg bend with a 2:1 inlet and a 1:1 aspect ratio outlet channel were validated against experimental results in terms of spatially resolved heat transfer distributions, pressure losses, and velocity distributions. The numerical domain consisted of one rib segment in the inlet channel and three ribs segments in the outlet channel to reduce the overall numerical effort and allow for an extensive parametric study. The results showed good agreement for both heat transfer magnitudes and spatial distributions, and the numerical results captured the predominate flow physics resulting from the 180 deg bend. The production of Dean vortices and acceleration of the flow in the bend produced strongly increased heat transfer on both the ribbed and unribbed walls in the outlet channel in addition to increases due to the ribs. Numerical simulations were performed for a wide range of divider wall-to-tip wall distances, which influenced the position of the highest heat transfer levels on the outlet walls and changed the shape of the heat transfer distribution on the tip wall. Analysis of section averages of heat transfer in the bend and outlet channel showed a strong influence of the tip wall distance, while no effect was seen upstream of the bend. A similarly large effect on pressure losses in the bend was observed with varying tip wall position. Trends in averaged heat transfer varied linearly with tip wall distance, while pressure losses followed a nonlinear trend, resulting in an optimum tip wall distance with respect to heat transfer efficiency.
Internal cooling channels with differing aspect ratios are typically found in gas turbine blades due to the varying thickness of the blade from the leading to trailing edge. These serpentine passages often contain several 180° bends, which are sharp edged in the region of the blade tip. The 180° bend has a pronounced effect on the heat transfer characteristics in the outlet channel and tip wall, where a strong influence is seen due to the divider wall-to-tip wall distance in the bend. The present study investigates the effect of the divider wall-to-tip wall distance for a ribbed two-pass cooling channel with a 2:1 inlet and 1:1 outlet channel. Spatially resolved heat transfer measurements were made using the transient thermochromic liquid crystal technique for a smooth and a ribbed configuration using parallel 45° ribs. Effects of the 180° bend on heat transfer and rib-induced enhancements were identified separately and bend effects were found to dominate the heat transfer increase in the outlet channel near the bend. Pressure losses due to the bend and ribs were also independently evaluated for a range of tip wall distances. Results show that the smaller tip wall distances increase heat transfer on the tip wall and outlet channel, but at the cost of an increased pressure loss. An optimum tip wall position is suggested, forming a compromise between heat transfer improvement and increased pressure losses.
This paper presents the combined effects of high turbulence and film cooling on the dispersion of a simulated hot streak as it passes over a scaled-up nozzle guide vane. Experimental data demonstrates a considerable decay in the strength of a hot streak due to turbulence effects alone. Film cooling further reduces the peak temperature values resulting in a reduction of the peak temperature in the hot streak on the order of 75% relative to the upstream peak temperature in the hot streak. Comparisons are made between high turbulence ͑Tuϭ20%͒ and moderate turbulence ͑Tuϭ3.5%͒ as well as between different blowing conditions for the suction side, showerhead, and pressure side film cooling holes on a simulated nozzle guide vane.
A novel heat flux sensor was tested which allows for time-resolved heat flux measurements in internal ribbed channels related to the study of passages in gas turbine blades. The working principle of the Atomic Layer Thermopile (ALTP) sensor is based on a thermoelectric field created by a temperature gradient over an YBCO crystal (the transverse Seebeck effect). The sensors very fast frequency response allows for highly time-resolved heat flux measurements up to the 1 MHz range. This paper explains the design and working principle of the sensor, as well as the benchmarking of the sensor for several flow conditions. For internal cooling passages, this novel sensor allows for highly accurate, time-resolved measurements of heat transfer coefficients, leading to a greater understanding of the influence of fluctuations in temperature fields.
Numerical results for an internal ribbed cooling channel including a 180° bend with a 2:1 inlet and 1:1 aspect ratio outlet channel were validated against experimental results in terms of spatially resolved heat transfer distributions, pressure losses, and velocity distributions. The numerical domain consisted of one rib segment in the inlet channel and three ribs segments in the outlet channel to reduce the overall numerical effort and allow for an extensive parametric study. The results showed good agreement for both heat transfer magnitudes and spatial distributions and the numerical results captured the predominate flow physics resulting from the 180° bend. The production of Dean vortices and acceleration of the flow in the bend produced strongly increased heat transfer on both the ribbed and unribbed walls in the outlet channel in addition to increases due to the ribs. Numerical simulations were performed for a wide range of divider wall-to-tip wall distances, which influenced the position of the highest heat transfer levels on the outlet walls and changed the shape of the heat transfer distribution on the tip wall. Analysis of section averages of heat transfer in the bend and outlet channel showed a strong influence of the tip wall distance while no effect was seen upstream of the bend. A similarly large effect on pressure losses in the bend was observed with varying tip wall position. Trends in averaged heat transfer varied linearly with tip wall distance while pressure losses followed a non-linear trend, resulting in an optimum tip wall distance with respect to heat transfer efficiency.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.