No abstract

Finding suitable non-expensive electrocatalyst materials for methanol oxidation is a significant challenge. Waste valorization of spent wastewater nanoadsorbents is a promising route toward achieving circular economy guidelines. In this study, the residual of layered double hydroxide (LDH) can be used as an electrocatalyst in direct methanol fuel cells as a novel approach. The Co–Ni–Zn–Fe LDH was prepared by the co-precipitation method followed by the adsorption of methyl orange (MO). Moreover, the spent adsorbent was calcined at different temperatures (200, 400, and 600 °C) to be converted to the corresponding mixed metal oxides (MMO). The prepared samples were characterized using XRD, FTIR, HRTEM, zeta potential, and hydrodynamic size measurements. The spent adsorbent was tested as an electro-catalyst for direct methanol electro-oxidation. The spent LDH/MO adsorbent showed a maximum current density of 6.66 mA/cm2 at a 50 mV/s scan rate and a 1 M methanol concentration. The spent MMO/MO adsorbent showed a maximum current density of 8.40 mA/cm2 at a 200 °C calcination temperature, 50 mV/s scan rate, and a 3 M methanol concentration. Both samples show reasonable stability over time, as indicated by the chronoamperometric response. Further nanoengineering of used nanoadsorbents could be a promising path to repurposing these wastes as electro-oxidation catalysts.

The preparation of adsorbents plays a vital role in the adsorption method. In particular, many adsorbents with high specific surface areas and unique shapes are essential for the adsorption strategy. A Zn–Mg–Al/layer double hydroxide (LDH) was designed in this study using a simple co-precipitation process. Adsorbent based on Zn–Mg–Al/LDH was used to remove crystal violet (CV) from the wastewater. The impacts of the initial dye concentration, pH, and temperature on CV adsorption performance were systematically examined. The adsorbents were analyzed both before and after adsorption using FTIR, XRD, and SEM. The roughness parameters and surface morphologies of the produced LDH were estimated using 3D SEM images. Under the best conditions (dose of adsorbent = 0.07 g and pH = 9), the maximum adsorption capacity has been achieved. Adsorption kinetics studies revealed that the reaction that led to the adsorption of CV dye onto Zn–Mg–Al/LDH was a pseudo-second-order model. Additionally, intraparticle diffusion suggests that Zn–Mg–Al/LDH has a fast diffusion constant for CV molecules (0.251 mg/(g min1/2)). Furthermore, as predicted by the Langmuir model, the maximal Zn–Mg–Al/LDH adsorption capacity of CV was 64.80 mg/g. The CV dimensionless separation factor (RL) onto Zn–Mg–Al/LDH was 0.769, indicating that adsorption was favorable. The effect of temperature was performed at 25, 35, and 45 °C in order to establish the thermodynamic parameters ∆Ho, ∆So, and ∆Go. The computed values indicated exothermic and spontaneous adsorption processes. The study presented here might be used to develop new adsorbents with enhanced adsorption capabilities for the purpose of protecting the water environment.

No abstract

The preparation of adsorbents plays a vital part in the adsorption method. In particular, many adsorbents with high specific surface areas and unique shapes are essential for the adsorption strategy. In this study, a Zn-Mg-Al/layer double hydroxide (LDH) had been designed via a facile co-precipitation process. Adsorbent based on Zn-Mg-Al/LDH was utilized to remove crystal violet (CV) from the wastewater. The impacts of the initial dye concentration, pH, and temperature on CV adsorption performance were systematically examined. The adsorbents were analyzed both before and after adsorption using FTIR, XRD, and SEM. The roughness parameters and surface morphologies of the produced LDH were estimated using 3D SEM images. Under the best conditions (dose of adsorbent = 0.07 g and pH = 9), the maximum adsorption capacity has been achieved. Adsorption kinetics studies revealed that the reaction that led to the adsorption of CV dye onto Zn-Mg-Al/LDH was a pseudo-second-order model. Additionally, intraparticle diffusion suggests that Zn-Mg-Al/LDH has fast diffusion constant for CV molecules (0.251 mg/(g.min1/2)). Furthermore, as predicted by the Langmuir model, the maximal Zn-Mg-Al/LDH adsorption capacity of CV was 64.80 mg/g. The CV adsorption equilibrium parameter (RL) onto Zn-Mg-Al/LDH was 0.769, indicating that adsorption was favorable. The effect of temperature was performed at 25, 35, and 45 oC in order to establish the thermodynamic parameters ∆Ho, ∆So, and ∆Go. The computed values indicated exothermic and spontaneous adsorption processes. The study presented here might be used to develop new adsorbents with enhanced adsorption capabilities for the purpose of protecting the environment of water. ‎