No abstract

Microplastic fibers, also known as microfibers, are the most abundant microplastic forms found in the environment. Microfibers are released in massive numbers from textile garments during home laundering via sewage effluents and/or sludge. This review presents and discusses the importance of synthetic textile-based microfibers as a source of microplastics. Studies focused on their release during laundering were reviewed, and factors affecting microfiber release from textiles and the putative role of wastewater treatment plants (WWTPs) as a pathway of their release in the environment were examined and discussed. Moreover, potential adverse effects of microfibers on marine and aquatic biota and human health were briefly reviewed. Studies show that thousands of microfibers are released from textile garments during laundering. Different factors, such as fabric type and detergent, impact the release of microfibers. However, a relatively smaller number of available studies and often conflicting findings among studies make it harder to establish definitive trends related to important factors contributing to the release of microfibers. Even though current WWTPs are highly effective in capturing microfibers, due to the presence of a massive number of microfibers in the influent, up to billions of fibers per day are released through effluent into the environment. There is a need to establish standardized protocols and procedures that can allow meaningful comparisons among studies to be performed.

Effective dissolution of cellulosic macromolecules is the first predominant step to prepare functional bio-based materials with desirable properties. In this study, we developed an improved dissolution process using a freeze-drying pretreatment to promote the dissolution of cellulose. Rheological measurements of cellulose solutions and physicochemical characterization of regenerated cellulose films (scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction, and thermogravimetric analysis) were performed. Cellulose solution prepared from 5% microcrystalline cellulose (w:v) in the solvent exhibits a Newtonian fluid character while cellulose solutions at higher concentrations show a pseudo-plastic fluid behavior. Results from physicochemical characterization indicate that a freeze-drying pretreatment step of cellulose leads to a complete dissolution at 5% concentration while only part of cellulose is dissolved at 10% and 15% concentrations. The results obtained indicated that the use of a freeze-drying pretreatment step under mild conditions lead to a complete dissolution of cellulose at 5% concentration. The cellulose films prepared from 5% concentration exhibited desirable properties such as good optical transparency, crystallinity, and thermal stability.

Biopolymers are polymeric materials derived from biological sources. Due to their renewability, abundance, biodegradability and other unique properties such as high adsorption capabilities and ease of functionalization they have been investigated for several industrial applications including sorption. Polysaccharides especially cellulose, chitin and chitosan are important biopolymers because of their high abundance, wide distribution and low cost of production. This chapter provides an overview of properties, common processing methods, and material characterization of three commonly studied biopolymers namely cellulose, chitin and chitosan. It provides a thorough review on recent developments on utilization of cellulose, chitin, and chitosan-based materials for various sorption applications. Specifically, their application and efficiency in organic dye removal, heavy metals removal, oil and solvent spillage cleanup, and CO 2 adsorption are presented and discussed.

Synthetic dyes have become an integral part of many industries such as textiles, tannin and even food and pharmaceuticals. Industrial dye effluents from various dye utilizing industries are considered harmful to the environment and human health due to their intense color, toxicity and carcinogenic nature. To mitigate environmental and public health related issues, different techniques of dye remediation have been widely investigated. However, efficient and cost-effective methods of dye removal have not been fully established yet. This paper highlights and presents a review of recent literature on the utilization of the most widely available biopolymers, specifically, cellulose, chitin and chitosan-based products for dye removal. The focus has been limited to the three most widely explored technologies: adsorption, advanced oxidation processes and membrane filtration. Due to their high efficiency in dye removal coupled with environmental benignity, scalability, low cost and non-toxicity, biopolymer-based dye removal technologies have the potential to become sustainable alternatives for the remediation of industrial dye effluents as well as contaminated water bodies.

As the most abundant natural polymer, cellulose is a prime candidate for the preparation of both sustainable and economically viable polymeric products hitherto predominantly produced from oil-based synthetic polymers. However, the utilization of cellulose to its full potential is constrained by its recalcitrance to chemical processing. Both fundamental and applied aspects of cellulose dissolution remain active areas of research and include mechanistic studies on solvent–cellulose interactions, the development of novel solvents and/or solvent systems, the optimization of dissolution conditions, and the preparation of various cellulose-based materials. In this review, we build on existing knowledge on cellulose dissolution, including the structural characteristics of the polymer that are important for dissolution (molecular weight, crystallinity, and effect of hydrophobic interactions), and evaluate widely used non-derivatizing solvents (sodium hydroxide (NaOH)-based systems, N,N-dimethylacetamide (DMAc)/lithium chloride (LiCl), N-methylmorpholine-N-oxide (NMMO), and ionic liquids). We also cover the subsequent regeneration of cellulose solutions from these solvents into various architectures (fibers, films, membranes, beads, aerogels, and hydrogels) and review uses of these materials in specific applications, such as biomedical, sorption, and energy uses.

To investigate the effective dissolution of high molecular weight (MW) cellulose macromolecules at ambient conditions, cellulose (DP > 4,000) derived from cotton fiber waste was dissolved in 1‐butyl‐3‐methylimidazolium acetate (BMIMAc)/N,N‐dimethylacetamide (DMAc) solvent in this study. High MW cotton cellulose achieves a solubility between 3% and 5% cellulose concentrations using BMIMAc/DMAc solvent at ambient conditions. Rheological studies showed that all cellulose/solvent solutions displayed a shear thinning behavior. Results from the physical characterization revealed that well‐dissolved cotton cellulose exhibited highly porous structure and the crystalline structure of cotton cellulose was highly disrupted during dissolution and regeneration processes. This study is the first to report on the ability of BMIMAc/DMAc solvent system to dissolve high MW cellulose under ambient conditions, which represents an energy‐saving and environmentally friendly approach. As cellulose used in this study was derived from low quality waste cotton fibers, the potential utilization of such cotton cellulose may create a competitive market for low quality cotton and target advanced applications of cellulose‐based products for green materials and energy. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018, 135, 45928.

This study reports on a strategy of using sol–gel and supercritical drying techniques to prepare aerocellulose monoliths with enhanced specific surface area and porosity by adding NaCl particles into the cellulose solution. The addition of 5 wt% of NaCl particles led to increased specific surface area of aerocellulose monoliths (from 114 m2/g to 205 m2/g), as well as their porosity (by ~5%). The aerocellulose monoliths prepared by adding NaCl particles achieved improved porous characteristics, lightweight, lower crystallinity, and better thermal stability, as compared to the control. This study demonstrates the effectiveness of NaCl particles to tune the surface area and the pore characteristics, which provides a facile route to achieve enhanced surface area and improved pore characteristics of aerocellulose monoliths.