The laser chemical machining is a non-conventional substractive processing method. It is based on the laser-activation of a material dissolution of metals in electrolyte ambient via local-induced temperature gradients and allows a gentle and smooth processing of especially temperature-sensitive metals. However, the material removal is characterized by a narrow process window and is restricted by occurring disturbances, which are supposed to be related to the localized electrolyte boiling. In order to control the removal quality and avoid disturbances, the correlation between the laser-induced temperatures and the resulting removal geometry has to be better understood. In this work an analytical modeling of the laser-induced temperatures at the surface of titanium based on a Green-function approach is presented. The main influencing factors (laser, electrolyte, material) as well as possible heat transfer into the electrolyte are included and discussed. To verify the calculated temperatures, single spot experiments are performed and characterized for titanium in phosphoric acid solution within laser irradiation of 1 s. The correlation between the temperature distribution and the resulting removal geometry is investigated based on a spatial superposition. Thereby, the bottom limit temperature is found to range between 63˚C and 70˚C whereas the upper limit is related to the nucleate boiling regime. Based on the performed correlation an indicator is identified to predict the ruling removal regime and thereby to reduce the experimental expenditure.
The surface and subsurface conditions of components are significant for their functional properties. Every manufacturing process step changes the surface condition due to its mechanical, chemical and/or thermal impact. The depth of the affected zone varies for different machining operations, and is predetermined by the process parameters and characteristics. Furthermore, the initial state has a decisive influence on the interactions that lead to the final surface conditions. The aim of the investigation presented here is to compare the influence of the load characteristics over the depth applied to manufactured components by several different machining operations and to determine the causing mechanisms. In order to ensure better comparability between the surface modifications caused by different machining operations, the same material was used (AISI 4140; German steel grade 42CrMo4 acc. to DIN EN 10083-3) and annealed to a ferritic-pearlitic microstructure. Based on interdisciplinary cooperation within the collaborative research center CRC/Transregio 136 “Process Signatures”, seven different manufacturing processes, i.e., grinding, turning, deep rolling, laser processing, inductive heat treatment, electrical discharge machining (EDM) and electrochemical machining (ECM), were used, and the resulting surface zones were investigated by highly specialized analysis techniques. This work presents the results of X-ray measurements, hardness measurements and electron microscopic investigations. As a result, the characteristics and depths of the material modifications, as well as their underlying mechanisms and causes, were studied. Mechanisms occurring within 42CrMo4 steel due to thermal, mechanical, chemical or mixed impacts were identified as phase transformation, solidification and strengthening due to dislocation generation and accumulation, continuum dynamic recrystallization and dynamic recovery, as well as chemical reactions.
Laser-induced thermochemical polishing (LCP) is a non-conventional processing technique that uses laser radiation to smooth the surface of self-passivated metallic parts by initiating a localized anodic material dissolution. This technology can be used to selectively micro-polish without the need for masking or thermal and mechanical stress. However, there is still a lack in understanding the surface quality depending on the applied laser machining parameters. This paper takes up the concept of Process Signatures and interprets the surface smoothing as result of multiple, recurring internal material loads of a constant energy amount. The laser-induced thermal impact is identified as the relevant internal material load and is correlated with the surface roughness. This derives an empirical-based functional relation as multi-cycle Process Signature. The experiment results show an exponential decay in surface roughness with increasing cycle loads for titanium, Ti6Al4V, Nitinol, Stellite 21, and metallic glass. The Process Signature of LCP is a solution to a differential equation with respect to the cycle loads. The paper demonstrates how the multi-cycle Process Signature helps determine suitable machining parameters to predict the surface roughness, as well as to scale the polishing rate.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.