The preparation of amorphous solid dispersion (ASD) formulations is a promising strategy to improve the bioavailability of an active pharmaceutical ingredient (API). By dissolving the API in a polymer it is stabilized in its amorphous form, which usually shows higher water solubility than its crystalline counterpart. To prevent recrystallization, the long-term physical stability of ASD formulations is of big interest. In this work, the solubility of the APIs acetaminophen and naproxen in the excipient polymers poly(vinylpyrrolidone) (PVP K25) and poly(vinylpyrrolidone-co-vinyl acetate) (PVPVA64) was calculated with three models: the Perturbed-Chain Statistical Associating Fluid Theory (PC-SAFT), the Flory-Huggins model (FH), and an empirical model (Kyeremateng et al., J. Pharm. Sci, 2014, 103, 2847-2858). PC-SAFT and FH were further used to predict the influence of relative humidity (RH) on the API solubility in the polymers. The Gordon-Taylor equation was applied to model the glass-transition temperature of dry ASD and at humid conditions. The calculations were validated by 18 months-long stability studies at standardized storage conditions, 25 °C/0% RH, 25 °C/60% RH, and 40 °C/75% RH. The results of the three modeling approaches for the API solubility in polymers agreed with the experimental solubility data, which are only accessible at high temperatures in dry polymers. However, at room temperature FH resulted in a lower solubility of the APIs in the dry polymers than PC-SAFT and the empirical model. The impact of RH on the solubility of acetaminophen was predicted to be small, but naproxen solubility in the polymers was predicted to decrease with increasing RH with both, PC-SAFT and FH. At 25 °C/60% RH and 40 °C/75% RH, PC-SAFT is in agreement with all results of the long-term stability studies, while FH underestimates the acetaminophen solubility in PVP K25 and PVPVA64.

No abstract

Inhibition of recrystallization of the drug substance in kinetically stabilized amorphous solid dispersions (ASDs) within and beyond shelf life is still a matter of debate. Generally, these ASD systems are considered to be prone to recrystallization, but examples of their long-term stability are emerging in the literature. Since, in some cases, the formation of crystals may impact bioavailability, recrystallization may present a relevant risk for patients as it potentially lowers the effective dose of the formulation. This study shows that such metastable formulations may indeed remain amorphous even after 15 years of storage under ambient conditions. A formulation of fenofibrate stored for 15 years was compared to a freshly prepared batch. A complete physicochemical characterization regarding content, purity, water content and glass transition was conducted. The emphasis of this physicochemical characterization was on crystallinity as a critical quality attribute: polarized light microscopy (PLM) was used as the standard qualitative method and X-ray powder diffraction (XRPD) as the standard quantitative method. An investigation of the crystal growth kinetics by transmission Raman spectroscopy (TRS) was conducted to build a predictive model. The model was applied successfully to predict the observed physical state of the 15-year-old samples. The observations presented here demonstrate that kinetic stabilization alone is able to prevent crystallization in ASDs over prolonged storage periods, suggesting the need for a reassessment of the risk perception for this kind of ASD formulations.

A series of amphiphilic diblock copolymers and triphilic triblock copolymer analogues of the architectures BA, CAB, and CBA have been synthesized and characterized with respect to their aggregation behavior in water. The A, B, and C components of the block copolymers are formed by hydrophilic poly(glycerol monomethacrylate) (PGMA), lipophilic poly(propylene oxide) (PPO), and a fluorophilic perfluoroalkyl segment, respectively. Their critical micelle concentrations in water are determined from surface tension measurements. The aggregation behavior of the copolymers, as investigated by DLS, SANS, AFM, and TEM, is found to be governed by the strong immiscibility between the lipophilic PPO blocks and the fluorophilic perfluorocarbon segments as well as the blocks sequence. It is found that the BA and CBA copolymers form clear micellar solutions in contrast to the CAB copolymer solutions which exhibit phase-separation above the LCST of the PPO block.

The purpose of this work is to compare the long-term physical stability of amorphous solid dispersion (ASD) formulations based on three different commercially used excipients, namely, poly(vinylpyrrolidone) K25 (PVP), poly(vinylpyrrolidone-co-vinyl acetate) (PVPVA64), and hydroxypropyl methylcellulose acetate succinate 126G (HPMCAS), at standardized ICH storage conditions, 25 °C/0% relative humidity (RH), 25 °C/60% RH, and 40 °C/75% RH. Acetaminophen (APAP) and naproxen (NAP) were used as active pharmaceutical ingredients (APIs). 18 month long stability studies of these formulations were analyzed and compared with the API/polymer phase diagrams, which were modeled and predicted by applying the Perturbed-Chain Statistical Associating Fluid Theory (PC-SAFT) and the Gordon-Taylor or Kwei equation. The study showed that, at dry storage, the solubility of the APIs in the polymers and the kinetic stabilizing ability of the polymers increase in the following order: HPMCAS < PVPVA64 < PVP. RH significantly reduces the kinetic stabilization as well as NAP solubility in the polymers, while the impact on APAP solubility is small. The impact of RH on the stability increases with increasing hydrophilicity of the pure polymers (HPMCAS < PVPVA64 < PVP). The experimental stability results were in very good agreement with predictions confirming that PC-SAFT and the Kwei equation are suitable predictive tools for determining appropriate ASD compositions and storage conditions to ensure long-term physical stability.