No abstract

The present study explores the possibilities of using locally available inexpensive waste prawn shell derived chitin reinforced and bioabsorbable polylactic acid (PLA) laminated composites to develop new materials with excellent mechanical and thermal properties for implantable application such as in bone or dental implant. Chitin at different concentration (1–20% of PLA) reinforced PLA films (CTP) were fabricated by solvent casting process and laminated chitin-PLA composites (LCTP) were prepared by laminating PLA film (obtained by hot press method) with CTP also by hot press method at 160 °C. The effect of variation of chitin concentration on the resulting laminated composite's behavior was investigated. The detailed physico-mechanical, surface morphology and thermal were assessed with different characterization technique such as FT-IR, XRD, SEM and TGA. The FTIR spectra showed the characteristic peaks for chitin and PLA in the composites. SEM images showed an excellent dispersion of chitin in the films and composites. Thermogravimetric analysis (TGA) showed that the complete degradation of chitin, PLA film, 5% chitin reinforced PLA film (CTP2) and LCTP are 98%, 95%, 87% and 98% respectively at temperature of 500 °C. The tensile strength of the LCTP was found 25.09 MPa which is significantly higher than pure PLA film (18.55 MPa) and CTP2 film (8.83 MPa). After lamination of pure PLA and CTP2 film, the composite (LCTP) yielded 0.265–1.061% water absorption from 30 min to 24 h immerse in water that is much lower than PLA and CTP. The increased mechanical properties of the laminated films with the increase of chitin content indicated good dispersion of chitin into PLA and strong interfacial actions between the polymer and chitin. The improvement of mechanical properties and the results of antimicrobial and cytotoxicity of the composites also evaluated and revealed the composite would be a suitable candidate for implant application in biomedical sector.

In recent years, there has been increasing interest in developing green biocomposite for industrial wastewater treatment. In this study, prawn-shell-derived chitosan (CHT) and kaolinite rich modified clay (MC) were used to fabricate biocomposite beads with different compositions. Prepared composite beads were characterized by FTIR, and XRD, and SEM. The possible application of the beads was evaluated primarily by measuring the adsorption efficiency in standard models of lead (II) and methylene blue (MB) dye solution, and the results show a promising removal efficiency. In addition, the composites were used to remove Cr (VI), Pb (II), and MB from real industrial effluents. From tannery effluent, 50.90% of chromium and 39.50% of lead ions were removed by composites rich in chitosan and 31.50% of MB was removed from textile effluent by a composite rich in clay. Moreover, the composite beads were found to be activated in both acidic and basic media depending on their composition, which gives a scope to their universal application in dye and heavy metal removal from wastewater from various industries.

No abstract

No abstract

A novel composite material was prepared from prawn shell derived chitosan (CHT) and locally available kaolinite-rich modified Bijoypur clay (MC) using a facile technique in which dilute acetic acid was used as a solvent for dissolving chitosan and composite fabrication whereas distilled water was used for preparing the clay dispersion. Bijoypur clay mainly consists of kaolinite clay mineral and it was modified with the dodecyl amine to make it organophilic. Morphology and properties of the composites (different weight ratio of MC and CHT) have been studied and compared with those of pure CHT and MC. Purification and modification of Bijoypur clay were investigated by X-ray diffraction (XRD), X-ray fluorescence (XRF), and Fourier transformed infrared spectroscopy (FTIR) analyses. The fabrication of CHT-MC composites was confirmed by FTIR analysis. Thermogravimetric analysis (TGA) and differential scanning colorimetry (DSC) were used to investigate the thermal stability of the composites. It was observed that dispersed clay improves the thermal stability and enhances the hardness of the matrix systematically with the increase of clay loading. In this study, a better insolubility in both acidic and alkaline media of the composites is also observed compared to pure chitosan.

In recent decades, increased domestic and industrial activities have led to the release of various pollutants into the aquatic environment. A robust and eco-friendly technique for removing these pollutants from wastewater is a crucial need. Among existing technologies, adsorption is considered to be a simple, cost-effective, and sustainable method. Recently, chitosan−clay nanocomposites have emerged because of their high abundance, ease of fabrication, and efficacy as adsorbents. Quantitatively, this particular class of composites is capable of removing ∼99% of dyes, metals, and harmful negative ions from various solutions. Also, the composite is designed to remove a maximum of ∼94% of the targeted herbicides from media under investigation. This review summarizes important information about this adsorbent in removing micropollutants from various water sources. A short overview of the chemical structure and the modification of chitosan and clay, along with their interaction within the composite matrix and with contaminants, is presented. Finally, a critical analysis of the removal performance of these composites compared with that of other industrial adsorbents is provided. Future research directions are suggested on the basis of the technological challenges faced in the industrial implementation of these materials.

No abstract