A spatially localized seismic sequence originated few tens of kilometres offshore the Mediterranean coast of Spain, close to the Ebro river delta, starting on 2013 September 5, and lasting at least until 2013 October. The sequence culminated in a maximal moment magnitude M w 4.3 earthquake, on 2013 October 1. The most relevant seismogenic feature in the area is the Fosa de Amposta fault system, which includes different strands mapped at different distances to the coast, with a general NE-SW orientation, roughly parallel to the coastline. However, no significant known historical seismicity has involved this fault system in the past. The epicentral region is also located near the offshore platform of the Castor project, where gas is conducted through a pipeline from mainland and where it was recently injected in a depleted oil reservoir, at about 2 km depth. We analyse the temporal evolution of the seismic sequence and use full waveform techniques to derive absolute and relative locations, estimate depths and focal mechanisms for the largest events in the sequence (with magnitude mbLg larger than 3), and compare them to a previous event (2012 April 8, mbLg 3.3) taking place in the same region prior to the gas injection. Moment tensor inversion results show that the overall seismicity in this sequence is characterized by oblique mechanisms with a normal fault component, with a 30 • low-dip angle plane oriented NNE-SSW and a subvertical plane oriented NW-SE. The combined analysis of hypocentral location and focal mechanisms could indicate that the seismic sequence corresponds to rupture processes along shallow low-dip surfaces, which could have been triggered by the gas injection in the reservoir, and excludes the activation of the Amposta fault, as its known orientation is inconsistent with focal mechanism results. An alternative scenario includes the iterated triggering of a system of steep faults oriented NW-SE, which were identified by prior marine seismics investigations.

No abstract

For induced microseismicity associated with hydraulic fracturing, the frequency‐magnitude distribution is typically characterized by a falloff with increasing magnitude that is significantly faster than for seismicity along active fault systems. This characteristic may arise from a break in scale invariance, possibly due to mechanical layering that typifies fine‐grained sedimentary rocks in many shale gas and tight oil reservoirs. The latter would imply the presence of spatiotemporal magnitude correlations. Using three microseismic catalogs for well stimulations in widely separated locations with varying hydraulic‐fracturing methods, we show that events with similar magnitudes indeed tend to cluster in space and time. In addition, we show that the interevent time distribution can be described by a universal functional form characterized by two power laws. One exponent can be related to the presence of interevent triggering as in aftershock sequences and is a consequence of the Omori‐Utsu law. The other one is a reflection of the intrinsic spatial variation in the microseismic response rates. Taken together, these features are indicative of nontrivial spatiotemporal clustering of induced microseismicity and, hence, of direct relevance for time‐dependent seismic hazard assessment.

Reliable estimations of magnitude of completeness (M c ) are essential for a correct interpretation of seismic catalogues. The spatial distribution of M c may be strongly variable and difficult to assess in mining environments, owing to the presence of galleries, cavities, fractured regions, porous media and different mineralogical bodies, as well as in consequence of inhomogeneous spatial distribution of the seismicity. We apply a 3-D modification of the probabilistic magnitude of completeness (PMC) method, which relies on the analysis of network detection capabilities. In our approach, the probability to detect an event depends on its magnitude, source-receiver Euclidian distance and source-receiver direction. The suggested method is proposed for study of the spatial distribution of the magnitude of completeness in a mining environment and here is applied to a 2-months acoustic emission (AE) data set recorded at the Morsleben salt mine, Germany. The dense seismic network and the large data set, which includes more than one million events, enable a detailed testing of the method. This method is proposed specifically for strongly heterogeneous media. Besides, it can also be used for specific network installations, with sensors with a sensitivity, dependent on the direction of the incoming wave (e.g. some piezoelectric sensors). In absence of strong heterogeneities, the standards PMC approach should be used. We show that the PMC estimations in mines strongly depend on the source-receiver direction, and cannot be correctly accounted using a standard PMC approach. However, results can be improved, when adopting the proposed 3-D modification of the PMC method. Our analysis of one central horizontal and vertical section yields a magnitude of completeness of about M c ≈ 1 (AE magnitude) at the centre of the network, which increases up to M c ≈ 4 at further distances outside the network; the best detection performance is estimated for a NNE-SSE elongated region, which corresponds to the strike direction of the low-attenuating salt body. Our approach provides us with small-scale details about the capability of sensors to detect an earthquake, which can be linked to the presence of heterogeneities in specific directions. Reduced detection performance in presence of strong structural heterogeneities (cavities) is confirmed by synthetic waveform modelling in heterogeneous media.

No abstract