In this work, biodegradable films based on poly (lactic acid) (PLA) and corn thermoplastic starch (TPS), additivated with epoxidized cardoon oil plasticizer (ECO) at 3% by weight with respect to PLA mass fraction, were prepared by melt extrusion process and compression molding. The effect of ECO on structural, thermal, mechanical, barrier, and spectral optical properties of the films was investigated. Spectroscopic analysis evidenced the development of physical interaction between oil and polymers, mainly PLA. In addition, no oil migration occurrence was detected after six months of film preparation, as evidenced by oil mass evaluation by precipitation as well as by 1H-NMR methods, thus highlighting the good inclusion of oil inside the polymeric network. The plasticizing action of the oil induced a lean improvement of the interfacial adhesion between hydrophobic PLA and hydrophilic TPS, particularly accentuated in PLA80_ECO composition, as evidenced by morphological analysis of blend fracture surfaces. TGA data underlined that, differently from TPS-based films, PLA-based systems followed one degradative thermal profile suggesting a slight compatibilization effect of epoxidized oil in these films. The shifting of Tg values, by differential scanning calorimetry (DSC) analysis, indicated a weak miscibility at molecular level. Generally, in the investigated blends, the phase separation between PLA and TPS polymers was responsible for the mechanical properties failing; in particular, the tensile strength evidenced a negative deviation from the rule of mixtures, particularly marked in TPS-based blends, where no physical entanglements occurred between the polymers since their immiscibility even in presence of ECO. The epoxidized oil strongly improved the barrier properties (water vapor permeability (WVP) and oxygen permeability (O2P)) of all the films, likely developing a physical barrier to water and oxygen diffusion and solubilization. With respect to neat PLA, PL80 and PL80_ECO films evidenced the improvement of surface wettability, due to the presence of polar groups both in TPS (hydroxyl residues) and in epoxidized oil (oxirane rings). Finally, following to the conditioning in climatic chamber at T = 25 °C and RH = 50%, PLA80 film became opaque due to TPS water absorption, causing a light transmittance decreasing, as evidenced by spectral optical analysis.

No abstract

Cardoon seed oil (CO), derived from the nonedible Cynara cardunculus plant, growing in marginal and contaminated soils of Mediterranean regions, was successfully epoxidized (ECO) in a fed-batch modality. The cost-effective and environmentally friendly oils have been used as bioplasticizers of poly­(lactic acid) (PLA), to improve the overall properties and broaden its industrial applications as a biodegradable packaging material. Hence, physical blends and films of PLA, containing 3% by weight of CO and ECO, were prepared by melt extrusion and compression molding, and the effect of the both bioplasticizers on structural, thermal, and mechanical properties of the obtained films was investigated. Cardoon oils induced the decreasing of glass transition temperature due to PLA free volume enhancement. This effect was particularly marked in PLA–ECO film. Thermal stability of PLA was meaningfully improved upon addition of the oils, and the mechanical properties made evident the increase of PLA ductility, particularly enhanced in the PLA–ECO system, where the polymeric matrix and the oil showed stronger physical interaction and improved phase compatibility, as also revealed by spectroscopic and morphological analyses. Therefore, the plasticization action exerted by very low concentrations of epoxidized cardoon oil efficiently overcomes PLA drawbacks, thus encouraging the feasibility of its use as a bioplastic for packaging material.

Bio-based composites made of poly(L-lactic acid) (PLLA) and β-cyclodextrin/d-limonene inclusion complex (CD-Lim) were prepared by melt extrusion. Encapsulation of volatile d-limonene molecules within β-cyclodextrin cages was proven to be a successful strategy to prevent evaporation during high-temperature processing. However, small amounts of limonene were released upon processing, resulting in the plasticization of the polymeric matrix. Morphological analysis revealed good dispersion of the filler, which acted as a nucleating agent, favoring the growth of PLLA crystals. The composites′ lowered glass transition temperature upon the addition of CD-Lim was also proved by thermomechanical analysis (DMA). Moreover, DMA revealed constant stiffness of modified materials at room temperature, which is crucial in PLLA-based formulations.