No abstract

Erosion and erosion–corrosion tests of as-built Ti-6Al-4V manufactured by Selective Laser Melting were investigated using slurries composed of SiO2 sand particles and either tap water (pure water) or 3.5% NaCl solution (artificial seawater). The microhardness value of selective laser melting (SLM)ed Ti-6Al-4V alloy increased as the impact angle increased. The synergistic effect of corrosion and erosion in seawater is always higher than erosion in pure water at all impact angles. The seawater environment caused the dissolution of vanadium oxide V2O5 on the surface of SLMed Ti-6Al-4V alloy due to the presence of Cl− ions in the seawater. These findings show lower microhardness values and high mass losses under the erosion–corrosion test compared to those under the erosion test at all impact angles.

Selective laser sintering (SLS) becomes a promising technology for manufacturing complicated objects with small to moderate numbers from a wide range of polymeric and metallic powders. However, the fabrication parameters in the SLS process need to be tailored for each end-use fabricated product. Hence, it becomes extremely important to investigate the effects of fabrication parameters on the mechanical and morphological properties of SLS parts. For this purpose, the present experimental work is devoted to evaluating the effects of some important fabrication parameters, that have not received proper attention in the published literature, on the properties of cement-filled polyamide 12 (PA12) parts manufactured with the SLS technique. The effect of scanning vector length on the tensile, compressive, and flexural strength of manufactured PA12/white cement parts is investigated. Also, the end-of-vector (EOV) effect on the edge geometry of manufactured parts is studied. Moreover, the effect of incident laser power (LP) on the surface quality of fabricated SLS PA12/white cement parts is qualitatively evaluated. The results from this work revealed that the scanning vector length significantly affects the mechanical properties of SLS parts provided that the load is applied along the scanning vector direction. Also, it is noticed that excessive exposure to laser energy at layer edges can deteriorate the part’s edge and in some cases can cause localized heating and burning of the part’s edge and, eventually, can result in surface microcracks. Finally, the experiments confirmed that increasing the laser power can enhance the surface roughness of manufactured parts; however, excessive increase in laser power causes localized burning and initiation of surface microcracks.

The production of customized prostheses for the foot and ankle still relies on slow and laborious steps of the traditional plaster molding fabrication techniques. Additive manufacturing techniques where three-dimensional objects can be constructed directly based on the object’s computer-aided-design data in a layerwise manner has opened the door to new opportunities for manufacturing of novel and personalized medical devices. The purpose of the present study was to develop a new methodology for design and manufacturing of a customized silicone partial foot prosthesis via an indirect additive manufacturing process. Furthermore, the biomechanics of gait of a subject with partial foot amputation wearing the custom silicone foot prosthesis manufactured by the indirect additive manufacturing was characterized, in comparison with a matched healthy participant. This study has confirmed the possibility of producing silicone partial foot prosthesis by indirect additive manufacturing procedure. The amputated subject reported total comfort using the custom prosthesis during walking, as well as cosmetic advantages. The prosthesis restored the foot geometry and normalized many of gait characteristics. The findings presented here contribute to introduce a proper understanding of biomechanics of walking after wearing silicone partial foot prosthesis and are useful for prosthetists and rehabilitation therapists when treating patients after partial foot amputation.

Polyamide-12/Portland cement nanocomposite was prepared by using the exfoliated adsorption method. The fabricated nanocomposite was applied first time to remove Congo red (CR), brilliant green (BG), methylene blue (MB), and methyl red (MR) from the synthetic wastewater. The polymer nanocomposite was characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy, elemental mapping, Brunauer–Emmett–Teller surface area analysis, and X-ray diffraction. The adsorption was rapid and all the studied dyes were absorbed on the surface of the polymer nanocomposite in 90 min. The point of zero charge was found at pH 5 and the factors such as pH, time, and temperature were found to affect the adsorption efficiency. Freundlich isotherm and pseudo-second-order models well-fitted the adsorption isotherm and kinetics data, respectively. The calculated maximum adsorption capacity was 161.63, 148.54, 200.40, and 146.41 mg/g for CR, BG, MB, and MR, respectively. The mode of the adsorption process was endothermic, spontaneous, and physical involving electrostatic attraction. On an industrial scale, the high percentage of desorption and slow decrease in the percentage of adsorption after every five regeneration cycles confirm the potential, practicality, and durability of the nanocomposite as a promising and advanced adsorbent for decolorization of colored wastewater.

To enhance the properties of polyamide 12 (PA12/Nylon 12) manufactured by the selective laser sintering (SLS) process, micron-sized glass beads are used as a filler, and the resulting composite is known as glass bead-filled PA12 (PA 3200 GF). Despite PA 3200 GF basically being a tribological-grade powder, very little has been reported on the tribological properties of laser-sintered objects based on this powder. As the properties of SLS objects are orientation-dependent, this study is devoted to investigating the friction and wear characteristics of the PA 3200 GF composite sliding against the steel disc in the dry-sliding mode. The test specimens were aligned in the SLS build chamber along five different orientations (X-axis, Y-axis, Z-axis, XY-plane, and YZ-plane). Additionally, the interface temperature and the friction-induced noise were measured. The pin-shaped specimens were examined using a pin-on-disc tribo-tester for 45 min to investigate the steady-state tribological characteristics of the composite material. The results revealed that the orientation of build layers relative to the sliding plane was a ruling parameter that determined the dominant wear pattern and the wear rate. Accordingly, where build layers were parallel or inclined to the sliding plane, abrasive wear predominated, and wear rate became 48% higher than that of specimens with perpendicular build layers, for which adhesive wear predominated. Interestingly, a noticeable synchronous variation of adhesion and friction-induced noise was observed. Taken together, the results from this study can efficiently serve the goals of fabricating SLS-functional parts with customized tribological properties.

No abstract

Purpose The cement-filled PA12 manufactured by selective laser sintering (SLS) offers desirable mechanical properties; however, these properties are dependent on several fabrication parameters. As a result, SLS prototypes may exhibit orthotropic mechanical properties unless properly oriented in build chamber. This paper aims to evaluate the effects of part build orientation, laser energy and cement content on mechanical properties of cement-filled PA12. Design/methodology/approach The test specimens were fabricated by SLS using the “DTM Sinterstation 2000” system at which the specimens were aligned along six different orientations. The scanning speed was 914mm/s, scan spacing was 0.15mm, layer thickness was 0.1mm and laser power was 4.5–8Watt. A total of 270 tensile specimens, 270 flexural specimens and 135 compression specimens were manufactured and the tensile, compression and flexural properties of fabricated specimens were evaluated. Findings The experiments revealed orientation-dependent (orthotropic) mechanical properties of SLS cement-filled PA12 and confirmed that the parts with shorter scan vectors have enhanced flexural strength as compared with longer scan vectors. The maximum deviations of ultimate tensile strength, compressive strength and flexural modulus along the six orientations were 32%, 26% and 36%, respectively. Originality/value Although part build orientation is a key fabrication parameter, very little was found in open literature with contradictory findings about its effect on mechanical properties of fabricated parts. In this work, the effects of build orientation when combined with other fabrication parameters on the properties of SLS parts were evaluated along six different orientations.