Carbon nanotubes, first identified by Iijima, require for their production a source of elemental carbon and a transfer of energy that is specific to the type of source and the growth environment. Methods developed so far involve arc discharge, and vaporization using laser, pyrolysis and chemical vapour deposition of hydrocarbons. Here, we show growth of carbon nanofibres from radio-frequency plasma-enhanced chemical vapour deposition at room temperature, which was made possible by substituting the thermal energy requirements for the growth with plasma decomposition of methane on the Ni catalyst. Electron microscopy analysis provides evidence for a 'tip' growth model, with the Ni catalyst particle attached to the tip of the nanofibre. Energy-filtered imaging shows the Ni catalyst has a surface layer rich in carbon, consistent with the formation of a eutectic Ni-C droplet as a nucleation site for the carbon nanofibres, so that the carbon diffuses across the surface. The reduced distortion of the catalyst particles at low temperatures leads to a more uniform growth of the carbon nanofibres over large areas. The lower growth temperature allows for the removal of the silicon dioxide barrier layer associated with catalytic growth, and should allow in situ growth of nanofibres on relatively large areas of temperature-sensitive substrates, such as plastics, organics and even paper.

No abstract

Artificial sheet materials, known as MetaSurfaces, have been applied to fully control both space and surface waves due to their exceptional abilities to dynamically tailor wave fronts and polarization states, while maintaining small footprints. However, previous and current designs and manufactured MetaSurfaces are limited to specific types of surfaces. There exists no general but rigorous design methodology for MetaSurfaces with generic curvature. The aim of this paper is to develop an analytical approach to characterize the wave behavior over arbitrary curvilinear MetaSurfaces. The proposed method allows us to fully characterize all propagating and evanescent wave modes from the MetaSurfaces. We will validate the proposed technique by designing, realizing and testing an ultrathin MetaSurface cloak for surface waves. Good results are obtained in terms of bandwidth, polarization independence and fabrication simplicity.

In the last decade, a technique termed transformation optics has been developed for the design of novel electromagnetic devices. This method defines the exact modification of magnetic and dielectric constants required, so that the electromagnetic behaviour remains invariant after a transformation to a new coordinate system. Despite the apparently infinite possibilities that this mathematical tool introduces, one restriction has repeatedly recurred since its conception: limited frequency bands of operation. Here we circumvent this problem with the proposal of a full dielectric implementation of a transformed planar hyperbolic lens which retains the same focusing properties of an original curved lens. The redesigned lens demonstrates operation with high directivity and low side lobe levels for an ultra-wide band of frequencies, spanning over three octaves. The methodology proposed in this paper can be applied to revolutionise the design of many electromagnetic devices overcoming bandwidth limitations.

A study of graphene on metal nanotextured surfaces for ultra-broadband light trapping, blackbody absorbers, and thermal imaging.

Despite intensive research on optimizing the methods for depositing carbon encapsulated ferromagnetic nanoparticles, the effect of the carbon cages remains unclear. In the present work, the effect of the graphitic cages on the magnetization of the ferromagnetic core has been studied by comparing the magnetic properties of pure and carbon encapsulated Ni particles of the same size. The carbon encapsulated Ni particles were formed using an electric arc discharge in de-ionized water between a solid graphite cathode and an anode consisting of Ni and C in a mass ratio of Ni:C = 7:3. This method is shown to have potential for low cost production of carbon encapsulated Ni nanoparticle samples with narrow particle size distributions. X-ray diffraction (XRD) and high resolution transmission electron microscopy (HRTEM) analysis were used to study the crystallography, morphology, and size distribution of the encapsulated and pure Ni nanoparticle samples. The availability of encapsulated particles with various sizes allowed us to elucidate the role of carbon cages in size-dependent properties. Our data suggest that even though encapsulation is beneficial for protection against hostile chemical environments and for avoiding low proximity phenomena, it suppresses the saturation magnetization of the Ni cores.

A great deal of interest has reemerged recently in the study of surface waves. The possibility to control and manipulate electromagnetic wave propagations at will opens many new research areas and leads to lots of novel applications in engineering. In this paper, we will present a comprehensive modeling and design approach for surface wave cloaks, based on graded‐refractive‐index materials and the theory of transformation optics. It can be also applied to any other forms of surface wave manipulation, in terms of amplitude and phase. In this paper, we will present a general method to illustrate how this can be achieved from modeling to the final design. The proposed approach is validated to be versatile and allows ease in manufacturing, thereby demonstrating great potential for practical applications.

The need to grow high quality semiconducting hydrogenated amorphous carbon (a-C:H) thin films to allow n-type electronic doping by nitrogenation has lead us to deposit films with low paramagnetic defect density (1017 cm−3). The films were grown on the earthed electrode of a radio frequency driven plasma enhanced chemical vapor deposition system using methane, helium and a range of nitrogen concentrations as the precursor gases. The deposited films are shown to be polymer like. Changes in the chemical structure and relative bond fractions as a function of the nitrogen flow rate into the plasma chamber and ex situ annealing are reported. Particular attention is paid to changes in the film structure after annealing at 100 °C, since an increase in the E04 optical band gap is observed as a function of nitrogen flow after the anneal. This suggests a decrease in the defect density of the film.