Аннотация. Основная задача процесса обжига электродной продукции -получение обожженных изделий с заданными физико-механическими свойствами. В работе определены математические зависимости формирования качества обжигаемых изделий в период их высокотемпера-турного нагрева, выполнена идентификация полученных математических зависимостей на основе экспериментальных данных. Адекват-ные модели позволяют исследовать процессы формирования качества электродной продукции для различных температурных режимов и начальных условий обжига, а так же прогнозировать показатели качества обожженной электродной продукции. Проведен сопоставитель-ный анализ статистической, детерминированной и нейросетевой моделей прогнозирования качества обожженной электродной продукции.Ключевые слова: обжиг электродных материалов, формирование качества продукции, моделирование процесса обжига, прогноз показателей процесса. 10.17073/0368-0797-2016-3-197-203 Предприятия черной металлургии являются одними из основных потребителей электродной продукции при выплавке спецсталей в электропечах.
DOI:Одним из важнейших переделов производства электродной продукции, определяющим качествен-ные и экономические показатели, является обжиг в многокамерных печах. В отечественной промышлен-ности требования к качеству обожженной продукции определяются техническими условиями ТУ 1913-001-00200992-95. Обожженные электроды должны отвечать необходимым физико-химическим и механическим свойствам, таким как удельное электросопротивление, предел прочности на сжатие, действительная плот-ность, объемная плотность, реакционная способность в СО 2 , осыпаемость.Повышение качества электродов и обожженных анодов значительно снижает их удельный расход при использовании в процессах электролиза и электро-плавки. В работе [1] проведена оценка расхода анода при различных свойствах обожженных анодов. Пока-зано, что дополнительные издержки за счет высокого расхода анодов с проблемами качества равнозначны 96 долл/т Al. Необходимость прогнозирования показа-телей качества электродной продукции в зависимости от ее исходного состава и режимных параметров обжи-га очевидна.Проведение экспериментальных исследований по формированию качества обожженных изделий в про-мышленных и лабораторных условиях является чрез-вычайно трудоемким и затратным путем, поскольку процесс обжига занимает до 360 ч. Наиболее перспек-тивным направлением исследований является матема-тическое моделирование. Однако публикации в этой области крайне малочисленны. В работе [2] авторами приведены результаты экспериментальных исследова-ний по влиянию температуры обжига на свойства заго-товок диаметром 300 мм. На их основе получена стати-стическая модель формирования качества углеродных заготовок в виде системы полиноминальных уравнений регрессии. Адекватность полученных уравнений авто-рами не проверялась, а достигнутая относительная по-грешность определения свойств электродов составляет
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.