No abstract

Summary Is the composition of soil organic matter changed by adding compost? To find out we incubated biowaste composts with agricultural soils and a humus‐free mineral substrate at 5°C and 14°C for 18 months and examined the products. Organic matter composition was characterized by CuO oxidation of lignin, hydrolysis of cellulosic and non‐cellulosic polysaccharides (CPS and NCPS) and 13C cross‐polarization magic angle spinning nuclear magnetic resonance (CPMAS 13C‐NMR) spectroscopy. The lignin contents in the compost‐amended soils increased because the composts contained more lignin, which altered little even after prolonged decomposition of the composts in soil. A pronounced decrease in lignin occurred in the soils amended with mature compost only. Polysaccharide C accounted for 14–20% of the organic carbon at the beginning of the experiment for both the compost‐amended soils and the controls. During the incubation, the relative contents of total polysaccharides decreased for 9–20% (controls) and for 20–49% (compost‐amended soils). They contributed preferentially to the decomposition as compared with the bulk soil organic matter, that decreased between < 2% and 20%. In the compost‐amended agricultural soils, cellulosic polysaccharides were decomposed in preference to non‐cellulosic ones. The NMR spectra of the compost‐amended soils had more intense signals of O–alkyl and aromatic C than did those of the controls. Incubation for 18 months resulted mainly in a decline of O–alkyl C for all soils. The composition of the soil organic matter after compost amendment changed mainly by increases in the lignin and aromatic C of the composts, and compost‐derived polysaccharides were mineralized preferentially. The results suggest that decomposition of the added composts in soil is as an ongoing humification process of the composts themselves. The different soil materials affected the changes in soil organic matter composition to only a minor degree.

No abstract

The processing of plastics, particularly reinforced composites, necessitates the use of corrosion-and wear-resistant materials for tools that come into contact with the polymer. For such applications, plastic mold steels were developed that offer not only a good wear resistance due to the presence of carbides in a martensitic matrix, but also good corrosion resistance provided primarily by a sufficient amount of dissolved chromium. The common processing route for these high-alloyed materials is the hot isostatic pressing (HIP) of gas-atomized powders (PM-HIP). In this context, sintering plays an insignificant role, except for the processing of metalmatrix composites (MMCs). The development of novel wear-and corrosion-resistant MMCs based on plastic mold steels requires knowledge of the sintering behavior of prealloyed powders of such tool steels. It is well known that alloyed powders can be processed by supersolidus liquidphase sintering (SLPS), a method leading to almost full densification and to microstructures without significant coarsening effects. In this work, two different gas-atomized powders of plastic mold steels were investigated by computational thermodynamics, thermal analysis, sintering experiments, and microstructural characterization. The results show that both powders can be sintered to almost full density (1 to 3 pct porosity) by SLPS in a vacuum or a nitrogen atmosphere. Experimental findings on the densification behavior, nitrogen uptake, and carbide volume fractions are in good agreement with calculations performed by computational thermodynamics.

The use of nitrogen in martensitic stainless steels is limited by its solubility. Nitrogen solubility can be increased by alloying with elements such as Cr, Mn, and Mo and the use of pressure, such as in Pressurized ElectroSlag Remelting (PESR). Furthermore, the joint addition of C þ N increases their solubility. Solid-state nitriding can be used for case hardening or N-enrichment of steel powders before sintering. However, the resulting stabilization of austenite can be a drawback for martensitic steels. Besides cryogenic treatment below the martensite finish temperature, ausforming, that is, metal working above M s , could be promising. This contribution gives an overview about latest developments in N-rich martensitic stainless steels.