Evolutionary relationships among representatives of Apiaceae (Umbelliferae) subfamily Apioideae have been inferred from phylogenetic analyses of nuclear ribosomal DNA internal transcribed spacer (ITS 1 and ITS 2) and plastid rpoC1 intron sequences. High levels of nucleotide sequence variation preclude the use of the ITS region for examining relationships across subfamilial boundaries in Apiaceae, whereas the rpoC1 intron is more suitably conserved for family-wide phylogenetic study but is too conserved for examining relationships among closely related taxa. In total, 126 ITS sequences from subfamily Apioideae and 100 rpoC1 intron sequences from Apiaceae (all three subfamilies) and outgroups Araliaceae and Pittosporaceae were examined. Phylogenies estimated using parsimony, neighbor-joining, and maximum likelihood methods reveal that: (1) Apiaceae subfamily Apioideae is monophyletic and is sister group to Apiaceae subfamily Saniculoideae; (2) Apiaceae subfamily Hydrocotyloideae is not monophyletic, with some members strongly allied to Araliaceae and others to Apioideae + Saniculoideae; and (3) Apiaceae subfamily Apioideae comprises several well-supported subclades, but none of these coincide with previously recognized tribal divisions based largely on morphological and anatomical characters of the fruit. Four major clades in Apioideae are provisionally recognized and provide the framework for future lower level phylogenetic analyses. A putative secondary structure model of the Daucus carota (carrot) rpoC1 group II intron is presented. Of its six major structural domains, domains II and III are the most, and domains V and VI the least, variable.

We measured the influence of alternative versions of the Drosophila melanogaster myosin heavy chain relay domain on muscle mechanical properties. We exchanged relay domain regions (encoded by alternative versions of exon 9) between an embryonic (EMB) isoform and the indirect flight muscle isoform (IFI) of myosin. Previously, we observed no effect of exchanging the EMB relay domain region into the flight muscle isoform (IFI-9b) on in vitro actin motility velocity or solution ATPase measurements compared to IFI. However, in indirect flight muscle fibers, IFI-9b exhibited decreased maximum power generation (P(max)) and optimal frequency of power generation (f(max)) to 70% and 83% of IFI fiber values. The decrease in muscle performance reduced the flight ability and wing-beat frequency of IFI-9b Drosophila compared to IFI Drosophila. Previously, we found that exchanging the flight muscle specific relay domain into the EMB isoform (EMB-9a) prevented actin movement in the in vitro motility assay compared to EMB, which does support actin movement. However, in indirect flight muscle fibers EMB-9a was a highly effective motor, increasing P(max) and f(max) 2.5-fold and 1.4-fold, respectively, compared to fibers expressing EMB. We propose that the oscillatory load EMB-9a experiences in the muscle fiber reduces a high activation energy barrier between two strongly bound states of the cross-bridge cycle, thereby promoting cross-bridge cycling. The IFI relay domain's enhanced sensitivity to load increases cross-bridge kinetics, whereas the EMB version is less load-sensitive.

Structural interactions between the myosin converter and relay domains have been proposed to be critical for the myosin power stroke and muscle power generation. We tested this hypothesis by mutating converter residue 759, which interacts with relay residues I508, N509, and D511, to glutamate (R759E) and determined the effect on Drosophila indirect flight muscle mechanical performance. Work loop analysis of mutant R759E indirect flight muscle fibers revealed a 58% and 31% reduction in maximum power generation (P(WL)) and the frequency at which maximum power (f(WL)) is generated, respectively, compared to control fibers at 15 °C. Small amplitude sinusoidal analysis revealed a 30%, 36%, and 32% reduction in mutant elastic modulus, viscous modulus, and mechanical rate constant 2πb, respectively. From these results, we infer that the mutation reduces rates of transitions through work-producing cross-bridge states and/or force generation during strongly bound states. The reductions in muscle power output, stiffness, and kinetics were physiologically relevant, as mutant wing beat frequency and flight index decreased about 10% and 45% compared to control flies at both 15 °C and 25 °C. Thus, interactions between the relay loop and converter domain are critical for lever-arm and catalytic domain coordination, high muscle power generation, and optimal Drosophila flight performance.

Grinding of ceramics is often treated as coarse grinding dominated by brittle fracture or fine grinding, at very low removal rates, dominated by plastic deformation. Through a set of experimental observations and analysis, it is shown that in grinding of ceramics the abrasive/work interaction can be treated similar to well known chip formation models. Such an approach permits the coexistence of ductile deformation and brittle fracture during the grinding of ceramics. When the grinding process is managed such that the brittle fracture is minimized, while maximizing the plastic deformation optimum results are achieved. In this regard it is conceivable to design ceramic grinding cycles, where the rough grinding cycle focuses on surface generation to achieve high material removal rate and productivity while minimizing brittle fracture and the finish grinding cycle focuses on surface generation which maximizes plastic deformation while still minimizing brittle fracture. While the above accounts for only one of four interactions in the grinding zone (viz) abrasive/work interaction, it is also necessary to address the other three interactions (viz) chip/bond, chip/work and bond/work interactions. The later considerations for ceramics grinding are identical to well established practices in metal grinding. When such grinding cycle optimization is carried out taking simultaneously into account the aspects of machine tool, grinding wheel, work material and operational factors, significant progress can be made in the grinding of ceramics. The results obtained through such systems approach are also described in this paper.

Stretch activation (SA) is critical to the flight ability of insects powered by asynchronous, indirect flight muscles (IFMs). An essential muscle protein component for SA and power generation is myosin. Which structural domains of myosin are significant for setting SA properties and power generation levels is poorly understood. We made use of the transgenic techniques and unique single muscle myosin heavy chain gene of Drosophila to test the influence of the myosin converter domain on IFM SA and power generation. Replacing the endogenous converter with an embryonic version decreased SA tension and the rate of SA tension generation. The alterations in SA properties and myosin kinetics from the converter exchange caused power generation to drop to 10% of control fiber power when the optimal conditions for control fibers -1% muscle length (ML) amplitude and 150 Hz oscillation frequency -were applied to fibers expressing the embryonic converter (IFI-EC). Optimizing conditions for IFI-EC fiber power production, by doubling ML amplitude and decreasing oscillation frequency by 60%, improved power output to 60% of optimized control fiber power. IFI-EC flies altered their aerodynamic flight characteristics to better match optimal fiber power generation conditions as wing beat frequency decreased and wing stroke amplitude increased. This enabled flight in spite of the drastic changes to fiber mechanical performance.