Pore water pressures (positive and negative) were monitored for four years (1996-1999) using a series of tensiometer-piezometers at increasing depths in a riverbank of the Sieve River, Tuscany (central Italy), with the overall objective of investigating pore pressure changes in response to flow events and their effects on bank stability. \ud The saturated/unsaturated flow was modelled using a finite element seepage analysis, for the main flow events occurring during the four-year monitoring period. Modelling results were validated by comparing measured with computed pore water pressure values for a series of representative events. Riverbank stability analysis was conducted by applying the limit equilibrium method (Morgenstern-Price), using pore water pressure distributions obtained by the seepage analysis. \ud The simulation of the 14 December 1996 event, during which a bank failure occurred, is reported in detail to illustrate the relations between the water table and river stage during the various phases of the hydrograph and their effects on bank stability. The simulation, according to monitored data, shows that the failure occurred three hours after the peak stage, during the inversion of flow (from the bank towards the river). A relatively limited development of positive pore pressures, reducing the effective stress and annulling the shear strength term due to the matric suction, and the sudden loss of the confining pressure of the river during the initial drawdown were responsible for triggering the mass failure. \ud Results deriving from the seepage and stability analysis of nine selected flow events were then used to investigate the role of the flow event characteristics (in terms of peak stages and hydrograph characteristics) and of changes in bank geometry. Besides the peak river stage, which mainly controls the occurrence of conditions of instability, an important role is played by the hydrograph characteristics, in particular by the presence of one or more minor peaks in the river stage preceding the main on

[1] The erosion of sediment from riverbanks affects a range of physical and ecological issues. Bank retreat often involves combinations of fluvial erosion and mass wasting, and in recent years, bank retreat models have been developed that combine hydraulic erosion and limit equilibrium stability models. In related work, finite element seepage analyses have also been used to account for the influence of pore water pressure in controlling the onset of mass wasting. This paper builds on these previous studies by developing a simulation modeling approach in which the hydraulic erosion, finite element seepage, and limit equilibrium stability models are, for the first time, fully coupled. Application of the model is demonstrated by undertaking simulations of a single flow event at a single study site for scenarios where (1) there is no fluvial erosion and the bank geometry profile remains constant throughout, (2) there is no fluvial erosion but the bank profile is deformed by simulated mass wasting, and (3) the bank profile is allowed to freely deform in response to both simulated fluvial erosion and mass wasting. The results are limited in scope to the specific conditions encountered at the study site, but they nevertheless demonstrate the significant role that fluvial erosion plays in steepening the bank profile or creating overhangs, thereby triggering mass wasting. However, feedbacks between the various processes also lead to unexpected outcomes. Specifically, fluvial erosion also affects bank stability indirectly, as deformation of the bank profile alters the hydraulic gradients driving infiltration into the bank, thereby modulating the evolution of the pore water pressure field. Consequently, the frequency, magnitude, and mode of bank erosion events in the fully coupled scenario differ from the two scenarios in which not all the relevant bank process interactions are included.

Riverbanks along the Arno River have been investigated with the aims of defining the main mechanisms of failure and retreat, their spatial distribution, and their causes. Geomorphological aspects were investigated by a reconnaissance of riverbank processes, for a number (26) of representative sites. Laboratory and in situ tests were then performed on a selected number of riverbanks (15). Based on the material characteristics, six main typologies of riverbanks have been defined, with homogeneous fine-grained and composite banks representing the most frequent types. Slab-type failures are the most frequent mechanism observed on fine-grained banks, while cantilever failures prevail on composite banks.The role of river stage and related pore water pressure distributions in triggering the main observed mechanisms of failure has been investigated using two different types of stability analysis. The first was conducted for 15 riverbanks, using the limit equilibrium method and considering simplified hypotheses for pore water pressure distribution (annulment of negative pore pressures in the portion of the bank between low water stage and peak stage). Stability conditions and predicted mechanisms of failure are shown to be in reasonably good agreement with field observations. Three riverbanks, representative of the main alluvial reaches of the river, were then selected for a more detailed bank stability analysis, consisting of: (a) definition of characteristic hydrographs of the reach with different return periods; (b) modelling of saturated and unsaturated flow using finite element seepage analysis; and (c) stability analysis with the limit equilibrium method, by adopting pore water pressure values derived from the seepage analysis. The results are compared to those obtained from the previous simplified analysis, and are used to investigate the different responses, in terms of stability, to different hydrological and riverbank conditions.

A severe rainstorm of high intensity occurred on 20th-21st November 2000, in the region of Pistoia, Tuscany, Italy, which triggered, within the entire province, over 50 landslides. These landslides can be broadly defined as complex earth slides-earth flows,originating as rotational slides that develop downslope into a flow. In this paper, two such landslides have been investigated by modelling the process of rainwater infiltration, the variations in both the positive and negative pore water pressures and their effect on slope stability during the storm. For both sites, results from morphometric and geotechnical analyses were used as a direct input to the numerical modelling. A modified Chu, 1978 approach was used to estimate the surface infiltration rate by adapting the original Green and Ampt, 1911 equations for unsteady rainfall intensity in conjunction with the surficial water balance. For transient conditions, a finite element analysis was used to model the fluctuations in pore water pressure during the storm, with the computed surface infiltration rate as the surface boundary condition. This was then followed by the application of the limit equilibrium Morgenstern and Price, 1965 slope-stability method, using the temporal pore water pressure distributions derived from the seepage analysis. From this methodology, a trend for the factor of safety was produced for both landslide sites. These results indicate that the most critical time step for failure was a few hours following the rainfall peak.

No abstract