Titanium alloy powder used for laser-based powder bed fusion (L-PBF) process is costly. One of the solutions is the inclusion of a powder recycling strategy, allowing unused or exposed powder particles to be recuperated post manufacture, replenished and used for future builds. However, during a L-PBF process, powder particles are exposed to high levels of concentrated energy from the laser. Particularly those in close proximity to the melt pool, leading to the formation of spatter and agglomerated particles. These particles can settle onto the powder bed, which can then influence the particle size distribution and layer uniformity. This study analysed extra-low interstitial (ELI) Ti6Al4V (Grade 23) powder when subjected to nine recycle iterations, tracking powder property variation across the successive recycling stages. Characterisation included chemical composition focusing upon O, N, and H content, particle size distribution, morphology and tapped and bulk densities. On review of the compositional analysis, the oxygen content exceeded the 0.13% limit for the ELI grade after 8 recycles, resulting in the degradation from Grade 23 level.
The properties of Extra Low Interstitials (ELI) Ti6Al4V components fabricated via the laser-based powder bed fusion (L-PBF) process are prone to variation, particularly throughout a powder reuse regime. Interstitial pick-up of interstitial elements within the build chamber during processing can occur, most notably, oxygen, nitrogen, and hydrogen, which can impair the mechanical properties of the built component. This study analyses ELI Ti6Al4V components manufactured by the L-PBF process when subjected to a nine-stage powder reuse sequence. Mechanical properties are reported via hardness measurement and tensile testing. Results showed that from 0.099 wt.% to 0.126 wt.% oxygen content, the mean hardness and tensile strength increased from 367.8 HV to 381.9 HV and from 947.6 Mpa to 1030.7 Mpa, respectively, whereas the ductility (area reduction) reduced from around 10% to 3%. Statistical analysis based on the empirical model from Tabor was performed to determine the strength–hardness relationship. Results revealed a significant direct relationship between tensile strength and Vickers hardness with a proportionality constant of 2.61 (R-square of 0.996 and p-value of 6.57 × 10−6).
The Laser-based Powder Bed Fusion (L-PBF) process uses a laser beam to selectively melt powder particles deposited in a layer-wise fashion to manufacture components derived from Computer-Aided Design (CAD) information. During laser processing, material is ejected from the melt pool and is known as spatter. Spatter particles can have undesirable geometries for the L-PBF process, thereby compromising the quality of the powder for further reuse. An integral step in any powder replenishing and reuse procedure is the sieving process. The sieving process captures spatter particles within the exposed powder that have a diameter larger than a defined mesh size. This manuscript reports on Ti6Al4V (Grade 23) alloy powder that had been subjected to seven reuse iterations, focusing on the characterisation of powder particles that had been captured (i.e., removed) by the sieving processes. Characterisation included chemical composition focusing upon interstitial elements O, N and H (wt.%), particle morphology and particle size analysis. On review of the compositional analysis, the oxygen contents were 0.43 wt.% and 0.40 wt.% within the 63 µm and 50 µm sieve-captured powder, respectively. Additionally, it was found that a minimum of 79% and 63% of spatter particles were present within the captured powder removed by the 63 µm and 50 µm sieves, respectively.
Lack of fusion (LOF) defects impact adversely on the mechanical properties of additively manufactured components produced via laser-based powder bed fusion. Following a stress-relieving heat treatment, the tensile properties and hardness of Ti6Al4V components were found to be negatively impacted by the presence of LOF defects. This work considers a geometrical-based inequality for the prediction of LOF defects. We critically evaluate an LOF criterion using both the experimentally and analytically obtained melt pool geometries. Experimentally, we determined melt pool dimensions by analysing a single-layer, multi-track deposition with oversized hatch spacing in order to establish depth and width from non-overlapping melt pools. Analytically, Rosenthal-based predictions of melt pool size (width and depth) are applied. To investigate LOF defects, we used hatch spacing as the main parameter variation to investigate defects while keeping all other controllable parameters unchanged. An original LOF criterion from the literature was found to be an adequate predictor of LOF defects when experimentally obtained melt pool geometry was used. Critically, however, the analytical expressions for melt pool geometry were found to be in error and this caused the LOF criterion to fail in predicting LOF defects in all cases where defects were observed experimentally. However, an adaptation to the LOF prediction criterion is proposed whereby it is recommended that a correction factor $${R}_{c}^{2}=0.7$$ R c 2 = 0.7 (or $${R}_{c}=0.83$$ R c = 0.83 ) is used with the analytically derived melt pool geometry. Furthermore, this correction is extended into the laser power versus scanning speed operating space to give minimum (corrected) line energy for LOF avoidance in Ti6Al4V components.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.