The use of fossil fuels in modern economies has been a success because of the low cost of fossil resources. However, the depletion of fossil reserves, the increase in waste production and global warming concerns have led to increased research on the production of biofuels from renewable resources. Waste production is steadily increasing in quantity and constantly changing in quality, creating enormous risks for the environment and, consequently, for the health of the population. This situation is much more worrying in developing countries, in particular because of the considerable delay in the field of the conversion and recovery of biomaterials, due to their difficulty in approaching the problem in a way that fits their context. The composition of such wastes and residues, rich in organic matter, allows their conversion via biochemical mechanisms, thus constituting an effective solution to address the environmental problems of their disposal. Anaerobic digestion remains a valuable and effective technology for transforming these biomaterials into biogas. The present review focuses on technologies, challenges and areas of application of biogas, especially in China and some African countries, in order to promote the large-scale use of biogas for electricity generation and biofuels. Results point out that China is more used to this technology, while African countries still rely on traditional and less advanced technologies, thus hampering the potential derived from the large availability of biomaterials. Both realities, however, share similar backgrounds about the dimension of the biogas plants and their non-commercial purposes, even if China is recently shifting toward the adoption of a different model. These considerations are used in the article to open an interesting new scenario of political alternatives which may provide a way out from poverty and economic dependence, within the framework of a wider circularity.

No abstract

The present work demonstrates the adsorption of hydroquinone (HQ) and resorcinol (R) by activated carbon based on shea residue (Vitellaria paradoxa). The adsorbent was prepared chemically by impregnation with sulfuric acid and coded by the acronym CAK-S. The central composite design (CCD) was used to optimize the main factors that influence the adsorption of HQ or R by activated carbon such as the initial concentration, the pH of the solution, the contact time, and the mass of the carbon on the expected response, which is the adsorbed quantity of the target pollutants. The optimal conditions obtained from the statistical analysis are as follows: concentration of 158 mg/L, pH 3, time of 120 min, and mass of 50 mg for the adsorption of HQ and concentration of 180 mg/L, pH 3, time of 86 min, and mass of 118 mg for the adsorption of R. The maximum quantities of HQ and R adsorbed are 45.02 mg/g and 33.65 mg/g, respectively. The analysis of variance (ANOVA) showed a good relationship between the variables involved with the coefficients of determination R2 = 98.69% for the adsorption of hydroquinone and R2 = 90.55% for that of resorcinol, which means that the model is more suitable to express the adsorbed amount according to the four optimized parameters. The experimental data obtained under these optimal conditions were simulated with two and three parameter nonlinear isotherm models as well as kinetic models. The results show that Elovich kinetic model better describes the adsorption of HQ and R, indicating chemisorption with heterogeneous active sites on the surface of CAK-S. Temkin’s two-parameter model shows that adsorption occurs on heterogeneous surfaces with a nonuniform adsorption energy distribution at the surface and Sips’s three-parameter model confirms the heterogeneity of the surface with a localized adsorption of HQ or R by CAK-S. The thermodynamics study has shown that the adsorption is endothermic ( Δ H 0   > 0 ) and spontaneous ( Δ G 0 < 0 ).

No abstract

In this work, biomass lignocellulosic materials extracted via chemical and physical treatments from bean and pistachio pod waste were used for the optimized elimination of Indigo Carmine (IC) from aqueous medium, using a design of experiments methodology. The physicochemical properties of the studied materials (raw and treated counterparts) used for the sorption of IC were investigated by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM) coupled with EDX, and thermal analysis. Key variables influencing the adsorption of IC, namely the initial IC concentration, the pH of the solution, the stirring time and the mass of adsorbents, were optimized by the central composite design (CCD) with three center points, the measured response being the amount of IC adsorbed. The optimal conditions obtained from the statistical analysis for the removal of IC were as follows: maximum adsorbed amounts of IC: 1.81 mg/g, 2.05 mg/g, 3.56 mg/g; 7.42 mg/g, 8.95 mg/g, 15.35 mg/g, for raw bean pods (RBS), BST1 and BST2 (bean pods chemically treated), and for raw pistachio pods (RPS), PST1 and PST2 (pistachio pods chemically treated), respectively. The pseudo-second-order nonlinear kinetics model well described the IC adsorption kinetics for RBS, BST1 and BST2, while the Elovich model was properly fitted by RPS, PST1, and PST2 biomaterials data. The Freundlich isotherm best described the shrinkage of IC on different sorbents. The good correlation of the experimental data of the IC with respect to the Freundlich isotherm indicated a multilayer adsorption with heterogeneous adsorption sites and different energies. The interest of this work consisted in developing analytical methods for the treatment of water polluted by dyes by using biosorbents, local biological materials widely available and inexpensive. The results collected in this work highlighted the interesting structural, morphological, and physico-chemical properties of the agro-waste used in the study, which properties allowed an important fixation of the target dye in solution. The research showed that the agro-waste used in the study are possible precursors to locally manufacture adsorbents at low cost, thus allowing the efficient removal of waste and dyes in liquid effluents.

The present work aims on the one hand to optimize the main influencing factors in the synthesis of activated carbon obtained from coffee husk as a widely available lignocellulosic precursor,...

The production of methyl esters (biodiesel) by the transesterification of Podocarpus falcatus oil (PFO) with methanol was optimized by response surface methodology (RSM) using the Box-Behnken design. The effects of parameters such as temperature, reaction time, and alcohol/oil molar ratio using yield and viscosity as responses were investigated. The optimum conditions for the production of biodiesel were as follows: temperature at 65°C, reaction time of 180 min, and molar ratio of 10 : 1, while the minimum viscosity was obtained for a temperature of 50°C, a reaction time of 120 min, and a molar ratio of 10 : 1. Physicochemical characterization by infrared spectroscopy (FT-IR) and UV visible spectroscopy showed that the free fatty acid (FFA) content of Podocarpus oil was 1.9%, which is less than the maximum of 2% recommended for the application of the one-step alkaline transesterification process. Also, the biodiesel obtained from the oil was seen to consist mainly of methyl esters, and that its physicochemical characteristics are within the standard set by the American Standard for Testing and Materials (ASTM).

Tea has received a lot of attention over the past few decades as the second most consumed beverage in the world after water.