No abstract

This study focuses on the treatment of a mature landfill leachate by coagulation and photo-Fenton at different conditions. Optimal coagulation is carried out with ferric chloride in acid conditions; and with alum in near-neutral conditions, to minimize the use of sulphuric acid for pH adjustment (1 g/L vs. 7.2 g/L), the generation of sludge and the increase of conductivity in the final effluent. In both cases, a similar chemical oxygen demand (COD) removal is obtained, higher than 65%, which is high enough for a subsequent photo-Fenton treatment. However, the removal of absorbance at 254 nm (UV-254) was significantly higher with ferric chloride (83% vs. 55%), due to the important removal of humic acids at acid pH. The best results for coagulation are 2 g/L ferric chloride at initial pH = 5 and 5 g/L alum at initial pH = 7. After coagulation with ferric chloride, the final pH (2.8) is adequate for a homogeneous photo-Fenton using the remaining dissolved iron (250 mg/L). At these conditions, using a ratio H2O2/COD = 2.125 and 30 min contact time, the biodegradability increased from 0.03 to 0.51. On the other hand, the neutral pH after alum coagulation (6.7) allows the use of zero valent iron (ZVI) heterogeneous photo-Fenton. In this case, a final biodegradability of 0.32 was obtained, after 150 min, using the same H2O2/COD ratio. Both treatments achieved similar results, with a final COD, UV-254 and color removal greater than 90%. However, the economic assessment shows that the approach of ferric chloride + homogeneous photo-Fenton is much cheaper (6.4 €/m3 vs. 28.4 €/m3). Although the discharge limits are not achieved with the proposed combination of treatments, the significant increase of the pre-treated leachate biodegradability allows achieving the discharge limits after a conventional biological treatment such as sequencing batch reactor, which would slightly increase the total treatment cost.

The main obstacle for the implementation of reverse osmosis (RO) in a treatment chain to reuse the effluent of a newsprint mill as fresh water is the high silica content of the water, which produces severe scaling on the membrane, thus, limiting its recovery. Coagulation is one of the preferred methods to reduce silica concentration. Five aluminum based coagulants have been tested at five dosages (500-2500 ppm) and three pHs (8.3, 9.5 and 10.5). All products showed their best efficiency at the highest dosage and pH, with the exception of alum, that was more efficient at intermediate dosages. A combination of a polyaluminum nitrate sulphate with a cationic quaternary polyamine (PANS-PA2), was the most efficient and versatile coagulant. It removed 97% of silica (5 ppm residual silica) at the optimal conditions (pH 10.5, 2500 ppm) and it was very efficient (76% silica removal) at pH 8.3, avoiding the need of any pH adjustment, and minimizing the conductivity and pH increase of the treated waters as well as obtaining some removal of the organic colloidal matter (≈25%).

Interest has grown in bio-polymers as being environmental friendly alternatives to synthetic additives. In this work, two native chitosans with different molecular weights have been evaluated on a laboratory scale for their effectiveness for the removal of contaminants from papermaking process waters by dissolved air flotation (DAF). The use of chitosan quaternary derivatives and the use of the native chitosans in combination with anionic bentonite microparticles have also been tested. Results demonstrate a high efficiency of the native chitosan products at intermediate dosages and furthermore, their efficiency is enhanced by the combined addition of bentonite. For an equivalent removal of contaminants, the required dosage of chitosan is about half that the dosage required in absence of bentonite. Quaternary derivatives have not improved the efficiency of the native chitosan in this case. The optimum treatment would be 50 mg/L of native chitosan and 100 mg/L of bentonite where this treatment is capable of the removal of 83-89% turbidity (residual turbidity 210-320 NTU), 68-71% dissolved turbidity (residual dissolved turbidity of 22-24 NTU), 18-22% total solids (residual total solids of 2750-2900 mg/L) and 19-23% COD (1440-1525 mg/L). The low molecular weight native chitosan is more efficient than the medium molecular weight chitosan in all cases. The Focused Beam Reflectance Measurement (FBRM) is used to assess the aggregation process and to predict the separation efficiency of DAF units either with single or dual systems. The efficiency predicted through the FBRM technique is very similar to that obtained later in the DAF tests.

Closure of water circuits in papermaking is of vital importance for achieving a more sustainable and economic manufacturing of paper. The most important limiting factor for a further closure is the accumulation of dissolved and colloidal materials (DCM). The extent to which DCM can become enriched in the water depends not only on how many times water is reused but also on the degree to which this matter becomes reattached to the fibers and other solid components of the paper furnish. This study analyzes the accumulation of the most typical contaminants in newsprint (NP) and light weigh coated (LWC) paper production. Results show that the release of DCM depends on the present contaminant load in the waters: higher at low contaminant load and lower at high contaminant load. A simulation was carried out to analyze the differences between assuming a constant and a variable release of contaminants to waters. Important differences were observed, especially for at low fresh water consumption those species with a major affinity for the fibers.