We report a novel synthetic procedure for the high-yield synthesis of metal–organic frameworks (MOFs) with fcu topology with a UiO-66-like structure starting from a range of commercial Zr IV precursors and various substituted dicarboxylic linkers. The syntheses are carried out by grinding in a ball mill the starting reagents, namely, Zr salts and the dicarboxylic linkers, in the presence of a small amount of acetic acid and water (1 mL total volume for 1 mmol of each reagent), followed by incubation at either room temperature or 120 °C. Such a simple “shake ‘n bake” procedure, inspired by the solid-state reaction of inorganic materials, such as oxides, avoids the use of large amounts of solvents generally used for the syntheses of Zr-MOF. Acidity of the linkers and the amount of water are found to be crucial factors in affording materials of quality comparable to that of products obtained under solvo- or hydrothermal conditions.

The novel ZrIV-based perfluorinated metal–organic framework (PF-MOF) [Zr6O4(OH)4(TFS)6] (ZrTFS) was prepared under solvent-free conditions using the commercially available tetrafluorosuccinic acid (H 2 TFS) as a bridging ditopic linker. Since H 2 TFS can be seen as the fully aliphatic and perfluorinated C4 analogue of fumaric acid, ZrTFS was found to be isoreticular to zirconium fumarate (MOF-801). The structure of ZrTFS was solved and refined from X-ray powder diffraction data. Despite this analogy, the gas adsorption capacity of ZrTFS is much lower than that of MOF-801; in the former, the presence of bulky fluorine atoms causes a considerable window size reduction. To have PF-MOFs with more accessible porosity, postsynthetic exchange (PSE) reactions on (defective) MOF-801 suspended in H 2 TFS aqueous solutions were carried out. Despite the different H 2 TFS concentrations used in the PSE process, the exchanges yielded two mixed-linker materials of similar minimal formulae [Zr6O4(μ3-OH)4(μ1-OH)2.08(H2O)2.08(FUM)4.04(HTFS)1.84] (PF-MOF1) and [Zr6O4(μ3-OH)4(μ1-OH)1.83(H2O)1.83(FUM)4.04(HTFS)2.09] (PF-MOF2) (FUM 2– = fumarate), where the perfluorinated linker was found to fully replace the capping acetate in the defective sites of pristine MOF-801. CO2 and N2 adsorption isotherms collected on all samples reveal that both CO2 thermodynamic affinity (isosteric heat of adsorption at zero coverage, Q st) and CO2/N2 adsorption selectivity increase with the amount of incorporated TFS 2– , reaching the maximum values of 30 kJ mol–1 and 41 (IAST), respectively, in PF-MOF2. This confirms the beneficial effect coming from the introduction of fluorinated linkers in MOFs on their CO2 adsorption ability. Finally, solid-state density functional theory calculations were carried out to cast light on the structural features and on the thermodynamics of CO2 adsorption in MOF-801 and ZrTFS. Due to the difficulties in modeling a defective MOF, an intermediate structure containing both linkers in the framework was also designed. In this structure, the preferential CO2 adsorption site is the tetrahedral pore in the “UiO-66-like” structure. The extra energy stabilization stems from a hydrogen bond interaction between CO2 and a hydroxyl group on the inorganic cluster.

Clean production of renewable fuels is a great challenge of our scientific community. Iridium complexes have demonstrated a superior catalytic activity in the water oxidation (WO) reaction, which is a crucial step in water splitting process. Herein, we have used a defective zirconium metal–organic framework (MOF) with UiO-66 structure as support of a highly active Ir complex based on EDTA with the formula [Ir(HEDTA)Cl]Na. The defects are induced by the partial substitution of terephthalic acid with smaller formate groups. Anchoring of the complex occurs through a post-synthetic exchange of formate anions, coordinated at the zirconium clusters of the MOF, with the free carboxylate group of the [Ir(HEDTA)Cl]− complex. The modified material was tested as a heterogeneous catalyst for the WO reaction by using cerium ammonium nitrate (CAN) as the sacrificial agent. Although turnover frequency (TOF) and turnover number (TON) values are comparable to those of other iridium heterogenized catalysts, the MOF exhibits iridium leaching not limited at the first catalytic run, as usually observed, suggesting a lack of stability of the hybrid system under strong oxidative conditions.

We report a novel synthetic procedure for the highyield synthesis of metal-organic frameworks with UiO-66 topology starting from a range of commercial Zr IV precursors and various substituted dicarboxylic linkers. The syntheses are carried out by grinding in a ball mill the starting reagents, namely Zr salts and the dicarboxylic linkers, in the presence of a small amount of acetic acid and water (1 mL total volume for 1 mmol of each reagent), followed by incubation at either room temperature or 120°C. Such a "shake 'n bake" procedure avoids the use of large amounts of solvents generally used for the syntheses of Zr-MOF. Acidity of the linkers and the amount of water are found to be crucial factors in affording materials of quality comparable to that of products obtained in solvo-or hydrothermal conditions.

Clean production of renewable fuels is a great challenge of our scientific community. Iridium complexes have demonstrated a superior catalytic activity in the water oxidation (WO) reaction, which is a crucial step in water splitting process. Herein we have used a defective zirconium MOF with UiO-66 structure as support of a highly active Ir complex based on EDTA with formula [Ir(HEDTA)Cl]Na. The defects are induced by the partial substitution of tereftalic acid with smaller formiate groups. Anchoring of the complex occurs through a post-synthetic exchange of formiate anions, coordinated at the zirconium clusters of the MOF, with the free carboxylate group of the [Ir(HEDTA)Cl]-complex. The modified material was tested as heterogenous catalyst for the WO reaction by using Cerium Ammonium Nitrate as sacrificial agent. Although TOF and TON values are comparable to those of other iridium heterogenized catalysts, the MOF exhibits iridium leaching not limited at the first catalytic run, as usually observed, suggesting a lack of stability of the hybrid system under strong oxidative conditions.