Organic semiconducting donor–acceptor polymers are promising candidates for stretchable electronics owing to their mechanical compliance. However, the effect of the electron‐donating thiophene group on the thermomechanical properties of conjugated polymers has not been carefully studied. Here, thin‐film mechanical properties are investigated for diketopyrrolopyrrole (DPP)‐based conjugated polymers with varying numbers of isolated thiophene moieties and sizes of fused thiophene rings in the polymer backbone. Interestingly, it is found that these thiophene units act as an antiplasticizer, where more isolated thiophene rings or bigger fused rings result in an increased glass transition temperature (Tg) of the polymer backbone, and consequently elastic modulus of the respective DPP polymers. Detailed morphological studies suggests that all samples show similar semicrystalline morphology. This antiplasticization effect also exists in para‐azaquinodimethane‐based conjugated polymers, indicating that this can be a general trend for various conjugated polymer systems. Using the knowledge gained above, a new DPP‐based polymer with increased alkyl side chain density through attaching alky chains to the thiophene unit is engineered. The new DPP polymer demonstrates a record low Tg, and 50% lower elastic modulus than a reference polymer without side‐chain decorated on the thiophene unit. This work provides a general design rule for making low‐Tg conjugated polymers for stretchable electronics.

Performed through side-chain engineering or by incorporating intramolecular locking units, the directionality and dynamic nature of noncovalent interactions are particularly attractive for the design of novel semiconducting materials in a wide variety of applications. This work investigates the nature and position of hydrogen bonding (intra- versus intermolecular), with the objective of developing a rational approach to the design of new semiconducting materials with improved properties in the solid state. To control the polymer chains’ self-assembly, a π-conjugated polymer incorporating a moiety capable of generating intramolecular hydrogen bonding is evaluated against a polymer that allows for intermolecular hydrogen bonding. Characterization through various techniques, optical spectroscopies, grazing incidence wide-angle x-ray scattering, and solution small-angle neutron scattering showed that intramolecular hydrogen bonds resulted in materials with improved crystallinity and higher effective conjugation in the solid state. Additionally, the effect of the noncovalent interaction configuration on the optoelectronic properties was analyzed in organic field-effect transistor fabrication. Devices prepared from the materials with intramolecular hydrogen bonds showed significantly higher performance, with three orders of magnitude higher charge mobility than their counterparts fabricated from polymers with intermolecular hydrogen bonds. These results confirm the importance of chemical design on polymer structures and offer a novel route for the design of high-efficiency semiconducting polymers for next-generation electronics.

Thermomechanical properties of polymers highly depend on their glass transition temperature (T g). Differential scanning calorimetry (DSC) is commonly used to measure T g of polymers. However, many conjugated polymers (CPs), especially donor–acceptor CPs (D–A CPs), do not show a clear glass transition when measured by conventional DSC using simple heat and cool scan. In this work, we discuss the origin of the difficulty for measuring T g in such type of polymers. The changes in specific heat capacity (Δc p) at T g were accurately probed for a series of CPs by DSC. The results showed a significant decrease in Δc p from flexible polymer (0.28 J g−1 K−1 for polystyrene) to rigid CPs (10−3 J g−1 K−1 for a naphthalene diimide‐based D–A CP). When a conjugation breaker unit (flexible unit) is added to the D–A CPs, we observed restoration of the Δc p at T g by a factor of 10, confirming that backbone rigidity reduces the Δc p. Additionally, an increase in the crystalline fraction of the CPs further reduces Δc p. We conclude that the difficulties of determining T g for CPs using DSC are mainly due to rigid backbone and semicrystalline nature. We also demonstrate that physical aging can be used on DSC to help locate and confirm the glass transition for D‐A CPs with weak transition signals. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019, 57, 1635–1644

Pyrazine-containing moieties were introduced into a semiconducting polymer to improve backbone planarity through a conformational locking effect, leading to good electronic properties and high stability in thin film transistors.