Este estudo teve por objetivo a caracterização energética do carvão de resíduos de cinco espécies provenientes de marcenarias no município de Gurupi, TO, bem como avaliar a influência do tempo e temperatura final de carbonização. Dos resíduos de cada uma das cinco espécies, foram obtidos vinte corpos de prova. O carvão vegetal foi obtido por meio da pirólise da madeira em forno tipo mufla, onde foram utilizadas duas marchas com temperaturas finais de carbonização de 450 °C e 500 °C e tempo de carbonização de 6 h e 7 h, respectivamente. Para a determinação da densidade aparente e do rendimento gravimétrico, os carvões foram pesados em balança analítica e medidos com paquímetro. A análise química imediata (AQI) foi realizada em forno mufla, para a determinação dos materiais voláteis, carbono fixo e cinzas, sendo também calculado o poder calorífico. O rendimento gravimétrico apresentou valores médios aceitáveis para todas as espécies e temperaturas (36,4%). Os teores de materiais voláteis (27,7%), carbono fixo (70,6%) e cinzas (1,7%) também foram considerados aceitáveis. O poder calorífico apresentou valores dentro dos padrões recomendados, apresentando alto potencial energético. A temperatura final de carbonização recomendada foi de 500 °C.
The objective of this work was to determine the quality of the Eucalyptus urophilla x Eucalyptus grandis clone charcoal, defining the basic density and wood retractability, apparent density, breaking index, charcoal yield, condensable and non-condensable gas yield, AQI and calorific values, comparing the results of different trunk positions and in two different heating ramps, ramp 1 (R1) with a heating rate of 1.25 ºC/min, final temperature of 450ºC and total of 6 hours, and ramp 2 (R2) with a heating rate of 1.19 ºC/min, final temperature of 500ºC and total time of 7 hours. The six evaluated trees were from a six-year-old cloned tree plantation located in the municipality of Gurupi, in the south of Tocantins state. The specimens for the characterizations were made from wooden discs removed from three trunk positions (base, DBH, top). The Eucalyptus urograndis wood presented basic density considered average (0.47 g/cm³) and good dimensional stability. The charcoal presented an expected yield and high calorific value influenced by the final temperature of the heating ramps, high fixed carbon content, acceptable ash content, as well as a low breaking rate. The results were satisfactory and identified the species as a good energy source.
We aimed to assess the quality of charcoal from three Eucalyptus and Corymbia citriodora species for energy production in the South of Tocantins state. A hybrid Eucalyptus urophylla x Eucalyptus grandis, the species Eucalyptus urophylla, Eucalyptus camaldulensis, and Corymbia citriodora were selected for the study. In the preparation of the material, 20 specimens of each species with the dimensions of 2.0 x 2.0 x 5.0 cm were made, being ten repetitions for each carbonization gait with different final temperatures and heating rates. The basic wood density, total gravimetric yield, total yields in condensable and non-condensable gases, immediate chemical analysis, and higher calorific value were determined. Corymbia citriodora presented higher wood basic density (0.583 g/cm³) and charcoal apparent density (0.459 g/cm³). In immediate chemical analysis, Eucalyptus urophylla and Corymbia citriodora presented the best averages among all species. The calorific value ranged from 7235.97 to 7573.98 (kcal/kg), considered an acceptable value for energy production. The final carbonization temperature of 550°C is recommended, with Eucalyptus urophylla and Corymbia citriodora presenting the best averages.
Pente-de-macaco (Apeiba tibourbou Aubl.) é uma espécie florestal que ocorre desde o norte do Brasil até Minas Gerais e São Paulo. Sua madeira, devido à baixa densidade é empregada na fabricação de pequenas embarcações; suas folhas e frutos decorativos potencializam o uso dessa espécie no paisagismo além ser usada na recuperação de áreas degradadas por ser uma planta pioneira e de rápido crescimento. Como suas sementes apresentam dormência por impermeabilidade do tegumento à água, objetivou-se neste trabalho avaliar a eficiência de tratamentos pré-germinativos para superar a dormência de suas sementes visando maximizar e uniformizar o processo de germinação. Foram estudados 8 tratamentos pré-germinativos: escarificação química com imersão por 5 minutos em H2SO4 nas concentrações de 50% e 25%, imersão em GA3 na concentração de 1g.L-1 por 24 e 48 horas, choque térmico à 80ºC e 100ºC, imersão em água destilada por 24 e 48 horas, além da testemunha. Foram avaliadas as porcentagens de germinação e o índice de velocidade de germinação das sementes. Os tratamentos escarificação química com imersão em H2SO4, imersão em água destilada e testemunha não obtiveram resultados significativos, imersão em GA3 por 24 e 48 horas somente uma semente germinou, choque térmico à 80ºC germinou 9,16% das sementes, entretanto o tratamento com choque térmico em água a 100ºC foi o tratamento mais eficaz para a superação da dormência de sementes de Apeiba tibourbou Aubl, ou seja, obtive-se um índice de germinação de 78,3%.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.