Non-intrusive, non-contacting frequency-domain photothermal radiometry (FD-PTR or PTR) and frequency-domain luminescence (FD-LUM or LUM) have been used with 659- and 830-nm laser sources to assess the pits and fissures on the occlusal surfaces of human teeth. Fifty-two human teeth were examined with simultaneous measurements of PTR and LUM and were compared to conventional diagnostic methods including continuous (dc) luminescence (DIAGNOdent), visual inspection and radiographs. To compare each method to the others, sensitivities and specificities were calculated by using histological observations as the gold standard. With the combined criteria of four PTR and LUM signals (two amplitudes and two phases), it was found that the sensitivity of this method was much higher than any of the other methods used in this study, whereas the specificity was comparable to that of dc luminescence diagnostics. Therefore, PTR and LUM, as a combined technique, has the potential to be a reliable tool to diagnose early pit and fissure caries and could provide detailed information about deep lesions. Using the longer wavelength (830-nm) laser source, it has been shown that detection of deeper subsurface lesions than the 659-nm probe provides is possible.

Nonintrusive, noncontacting frequency-domain photothermal radiometry (FD-PTR or PTR) and frequency-domain luminescence (FD-LUM or LUM) have been used with 659-nm and 830-nm laser sources to detect artificial and natural subsurface defects in human teeth. The major findings of this study are (1) PTR is sensitive to very deep (>5 mm) defects at low modulation frequencies (5 Hz). Both PTR and LUM amplitudes exhibit a peak at tooth thicknesses of ca. 1.4 to 2.7 mm. Furthermore, the LUM amplitude exhibits a small trough at ca. 2.5 to 3.5 mm. (2) PTR is sensitive to various defects such as a deep carious lesion, a demineralized area, an edge, a crack, and a surface stain, while LUM exhibits low sensitivity and spatial resolution. (3) PTR frequency scans over the surface of a fissure into demineralized enamel and dentin show higher amplitude than those for healthy teeth, as well as a pronounced curvature in both the amplitude and phase signal channels. These can be excellent markers for the diagnosis of subsurface carious lesions. (4) PTR amplitude frequency scans over the surface of enamels of variable thickness exhibit strong thickness dependence, thus establishing depth profilometric sensitivity to subsurface interfaces such as the dentin/enamel junction.

Frequency-domain photothermal radiometry (FD-PTR or PTR) is used to detect mechanical holes and demineralized enamel in the interproximal contact area of extracted human teeth. Thirty-four teeth are used in a series of experiments. Preliminary tests to detect mechanical holes created by dental burs and 37% phosphoric acid etching for 20 s on the interproximal contact points show distinct differences in the signal. Interproximal contact areas are demineralized by using a partially saturated acidic buffer system. Each sample pair is examined with PTR before and after micromachining or treating at sequential treatment periods spanning 6 h to 30 days. Dental bitewing radiographs showed no sign of demineralized lesion even for samples treated for 30 days. Microcomputer tomography (micro-CT), transverse microradiography (TMR), and scanning electron microscopy (SEM) analyses are performed. Although micro-CT and TMR measured mineral losses and lesion depths, only SEM surface images showed visible signs of treatment because of the minimal extent of the demineralization. However, the PTR amplitude increased by more than 300% after 80 h of treatment. Therefore, PTR is shown to have sufficient contrast for the detection of very early interproximal demineralized lesions. The technique further exhibits excellent signal reproducibility and consistent signal changes in the presence of interproximal demineralized lesions, attributes that could lead to PTR as a reliable probe to detect early interproximal demineralization lesions. Modulated luminescence is also measured simultaneously, but it shows a lower ability than PTR to detect these interproximal demineralized lesions.

Artificially created demineralized and remineralized carious lesions on the root and enamel of human teeth were examined by photothermal radiometry (PTR) and modulated luminescence (LUM). Fourteen extracted human teeth were used and a lesion was created on a 1 mmx4 mm rectangular window, spanning root to enamel, using a lactic acid-based acidified gel to demineralize the tooth surface. The lesion was then exposed to a remineralization solution. Each sample was examined with PTR/LUM on the root and enamel before and after treatment at times from 1 to 10 (5 on root) days of demineralization and 2 to 10 days of remineralization. Ten-day (5 on root) demineralized samples were remineralized. After completing all the experiments, transverse microradiography (TMR) analysis was performed to compare and correlate the PTR/LUM signals to the depth of lesions and mineral losses. The PTR and LUM amplitudes and phases showed gradual and consistent changes with treatment time. In this study, TMR showed good correlation coefficients with PTR and LUM. It was also found that the length of the treatment time did not correlate very well to any technique, PTR/LUM or TMR, which implies a significant degree of inhomogeneity of the demireralization and remineralization rates in each and every tooth.

A coupled diffuse-photon-density and thermal-wave model is developed for theoretical analysis of the photothermal field in demineralized teeth. Intact and demineralized layers of enamel, as well as dentin, are described as a layered one-dimensional system. The solution of the radiative transport equation in the limit of diffuse-photon-density field is considered as a source term in the thermal-wave field equation. The influence of optical parameters ͑absorption and scattering coefficients͒ and thermal parameters ͑thermal diffusivity and conductivity͒ of each layer on the diffuse-photon-density and thermal-wave depth profiles is analyzed using computer simulations, allowing the verification of accuracy and validity of the developed theory. The proposed model and simulations are intended for identifying the parameters most affecting the diffuse-photon-density and thermal-wave fields in turbid media, which leads to optimization of the fitting process of thermal and optical properties of teeth from experimental data obtained by frequency-domain photothermal radiometry.