No abstract

Within the limitations of this in vitro study, it can be stated that fibre posts can be recommended as a better alternative to the cast post and cores and prefabricated metallic posts in the anterior region and resin cement might give additional fracture resistance when used for post and crown cementation.

Introduction:Literature reveals that masticatory load on denture bearing tissues through complete dentures should be maximum on primary stress bearing areas and least on relief area in accordance with the histology of underlying tissues. A study to validate the existing beliefs was planned to compare the pressure on mucosa using selective pressure technique and minimal pressure technique, with the incorporation of two different impression materials utilizing the pressure sensors during secondary impression procedure.Materials and Methods:The study was performed using a maxillary analog. Three pressure sensors were imbedded in the oral analog, one in the mid palatine area and the other two in the right and left ridge crest. Custom trays of two different configurations were fabricated. The two impression materials tested were light body and zinc oxide eugenol. A total of 40 impressions were made. A constant weight of 1 kg was placed, and the pressure was recorded as initial and end pressures.Results:A significant difference in the pressure produced using different impression materials was found (P < 0.001). Light body vinyl polysiloxane produced significantly lesser pressure than zinc oxide eugenol impression materials. The presence of relief did affect the magnitude of pressure at various locations.Conclusion:All impression materials produced pressure during maxillary edentulous impression making. Tray modification is an important factor in changing the amount of pressure produced. The impression materials used also had a significant role to play on the pressures acting on the tissues during impression procedure.Clinical Implication:Light body VPS impression material may be recommended to achieve minimal pressure on the denture bearing tissues in both selective as well as minimal pressure techniques.

Vertical dimension at rest a b s t r a c tIntroduction: The determination of physiologic rest position of the mandible to the maxillae is of paramount importance in almost all fields of dentistry. The stability of vertical dimension at rest has been controversial if the rest position of mandible remains constant throughout life or not. Despite of several studies on the rest position of the mandible and facial vertical dimension, certain fundamental disagreements remain unresolved. The present study aims to compare the vertical dimension at rest, before and after extraction and after rehabilitation with complete denture. Material & methods:This study was conducted in a total of ten randomly selected patients, who had some natural teeth present with one or more opposing posterior teeth with vertical occlusal stops but were advised for extraction because of poor prognosis. Digital lateral cephalograms were done and measurements recorded at three stages: prior to extraction of remaining natural teeth, post extraction and after complete denture rehabilitation.Results: Vertical dimension at rest was found to be greatest in post rehabilitation followed by pre-extraction than post extraction state. The differences in changes were found to be statistically significant. Conclusion: Vertical dimension at rest shows a decrease following extraction of natural teeth, the occlusal stops, and an increase on rehabilitation. It can be stated that vertical dimension at rest is not stable position and varies following extraction of natural teeth and rehabilitation.

No abstract

EdentulousComplete denture a b s t r a c t Clinical implication: The purpose of this study is to record the vertical distance between anterior attachment of lingual frenum and incisal edge of mandibular central incisors in dentulous subjects and then determine the mean vertical distance and to suggest guidelines for positioning of mandibular central incisors in complete dentures. Method: In this study, 150 dentulous subjects (75 males and 75 females) were chosen based on predecided inclusion criteria. A mandibular cast was obtained from irreversible hydrocolloid impression in modified stock trays for each subject. All subjects were instructed to elevate the tongue while the impressions were made. The vertical distance between the anterior attachment of the lingual frenum and incisal edges of mandibular central incisors was measured on the casts and then the values were statistically analyzed. Result: The distance between anterior attachment of lingual frenum (AALF) mesioincisal edge of mandibular central incisor (CI) in male, female and total (male þ female) subjects was measured. In males it ranged from 7.3 to 8.9 mm with mean (±SD) 8.29 ± 0.36 mm while in females it ranged from 7.1 to 9.0 mm with mean (±SD) 8.21 ± 0.38 mm. Conclusion: It is believed that the application of this anatomic relation can provide a reliable point for arranging and checking the position of the mandibular central incisors for complete dentures in patients with class I ridge relationship.

No abstract